TS3L110

QUAD SPDT HIGHBANDWIDTH 10/100 BASET LAN SWITCH

DIFFERENTIAL 8CHANNEL TO 4CHANNEL MULTIPLEXER/DEMULTIPLEXER

SCDS176 − SEPTEMBER 2004

5

POST OFFICE BOX 655303

electrical

characteristics

over

recommended

operating

free-air

temperature

range,

PARAMETER

TEST CONDITIONS

MIN

TYP†

MAX

UNIT

VIK

E, S

VCC = 3.6 V,

IIN = −18 mA

−1.8

V

IIH

E, S

VCC = 3.6 V,

VIN = 5.5 V

±1

µA

IIL

E, S

VCC = 3.6 V,

VIN = GND

±1

µA

Ioff

VCC = 0,

VO = 0 to 5.5 V ,

VI = 0

1

µA

ICC

VCC = 3.6 V,

II/O = 0,

Switch ON or OFF

0.7

1.5

mA

Cin

E, S

f = 1 MHz,

VIN = 0

2.5

3.5

pF

Cio(OFF)

I port

VI = 0,

f = 1 MHz,

Outputs open,

Switch OFF

3.5

5

pF

Cio(OFF)

Y port

VI = 0,

f = 1 MHz,

Outputs open,

Switch OFF

5.5

7

pF

Cio(ON)

I or Y port

VI = 0,

f = 1 MHz,

Outputs open,

Switch ON

10.5

13

pF

ron

VCC = 3 V

1.25 V

≤ VI ≤ VCC,

II = −10 mA to −30 mA

4

8

Ω

ron(flat)‡

VCC = 3 V

VI = 1.25 V and VCC,

II = −10 mA to −30 mA

1

Ω

∆ron§

VCC = 3 V,

1.25 V

≤ VI ≤ VCC,

II = −10 mA to −30 mA

0.9

2

Ω

VI, VO, II, and IO refer to I/O pins. VIN refers to the control inputs.

† All typical values are at VCC = 3.3 V (unless otherwise noted), TA = 25°C.

‡ ron(flat) is the difference of ron in a given channel at specified voltages.

§ ∆ron is the difference of ron in a given device.

switching characteristics over recommended operating free-air temperature range,

PARAMETER

FROM

(INPUT)

TO

(OUTPUT)

MIN

TYP†

MAX

UNIT

tpd¶

I or Y

Y or I

0.25

ns

tPZH, tPZL

E or S

I or Y

0.5

7

ns

tPHZ, tPLZ

E or S

I or Y

0.5

5

ns

tsk(p)#

I or Y

Y or I

0.1

0.2

ns

† All typical values are at VCC = 3.3 V (unless otherwise noted), TA = 25°C.

¶ The propagation delay is the calculated RC time constant of the typical ON-state resistance of the switch and the specified load capacitance when

driven by an ideal voltage source (zero output impedance).

# Skew between opposite transitions of the same output |tPHL − tPLH|. This parameter is not production tested.

dynamic

characteristics

over

recommended

operating

free-air

temperature

range,

PARAMETER

TEST CONDITIONS

MIN

TYP†

MAX

UNIT

XTALK

RL = 100 Ω,

f = 250 MHz, see Figure 7

−26

dB

OIRR

RL = 100 Ω,

f = 250 MHz, see Figure 8

−28

dB

BW

RL = 100 Ω, see Figure 6

500

MHz

† All typical values are at VCC = 3.3 V (unless otherwise noted), TA = 25°C.