Os motores de busca de Datasheet de Componentes eletrônicos |
|
MP2143 Folha de dados(PDF) 12 Page - Monolithic Power Systems |
|
MP2143 Folha de dados(HTML) 12 Page - Monolithic Power Systems |
12 / 14 page MP2143 – 3A, 5.5V, 1.2MHz, 40μA IQ, COT SYNCHRONOUS STEP-DOWN SWITCHER MP2143 Rev. 1.07 www.MonolithicPower.com 12 7/4/2016 MPS Proprietary Information. Patent Protected. Unauthorized Photocopy and Duplication Prohibited. © 2016 MPS. All Rights Reserved. APPLICATION INFORMATION COMPONENT SELECTION Setting the Output Voltage The external resistor divider sets the output voltage (see the Typical Application schematic on page 1). The feedback resistor R1 must account for both stability and dynamic response, and thus can not be too large or too small. Choose an R1 value between 120kΩ and 200kΩ. R2 is then given by: out R1 R2 V 1 0.6 The feedback circuit is shown as Figure 2. R1 R2 Vout FB MP2143 Figure 2: Feedback Network Table 1 lists the recommended resistors values for common output voltages. Table 1: Resistor Values for Common Output Voltages VOUT (V) R1 (kΩ) R2 (kΩ) 1.0 200(1%) 300(1%) 1.2 200(1%) 200(1%) 1.8 200(1%) 100(1%) 2.5 200(1%) 63.2(1%) 3.3 200(1%) 44.2(1%) Selecting the Inductor A 0.82µH to 4.7µH inductor is recommended for most applications. For highest efficiency, chose an inductor with a DC resistance less than 15mΩ. For most designs, the inductance value can be derived from the following equation. OUT IN OUT 1 IN L OSC V(V V ) L VI f Where ΔIL is the inductor ripple current. Choose an inductor current to be approximately 30% of the maximum load current. The maximum inductor peak current is: L L(MAX) LOAD I II 2 Selecting the Input Capacitor The input current to the step-down converter is discontinuous, and requires a capacitor to supply the AC current to the step-down converter while maintaining the DC input voltage. Use low-ESR capacitors for the best performance. Ceramic capacitors with X5R or X7R dielectrics are highly recommended because of their low ESR values and small temperature coefficients. For most applications, a 10µF capacitor is sufficient. For higher output voltage, use 47μF to improve system stability. Since the input capacitor absorbs the input switching current it requires an adequate ripple current rating. The RMS current in the input capacitor can be estimated by: IN OUT IN OUT LOAD 1 C V V 1 V V I I The worse case condition occurs at VIN = 2VOUT, where: 2 I I LOAD 1 C For simplification, choose an input capacitor whose RMS current rating greater than half of the maximum load current. The input capacitor can be electrolytic, tantalum or ceramic. When using electrolytic or tantalum capacitors, use a small high-quality ceramic capacitor (0.1μF), placed as close to the IC as possible. When using ceramic capacitors, make sure that they have enough capacitance to prevent excessive voltage ripple at input. The input voltage ripple caused by capacitance can be estimated by: LOAD OUT OUT IN IN SIN IV V V1 fC1 V V |
Nº de peça semelhante - MP2143 |
|
Descrição semelhante - MP2143 |
|
|
Ligação URL |
Privacy Policy |
ALLDATASHEETPT.COM |
ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |