Os motores de busca de Datasheet de Componentes eletrônicos |
|
M41ST95YMX6TR Folha de dados(PDF) 9 Page - STMicroelectronics |
|
M41ST95YMX6TR Folha de dados(HTML) 9 Page - STMicroelectronics |
9 / 35 page 9/35 M41ST95Y*, M41ST95W OPERATION The M41ST95Y/W clock operates as a slave de- vice on the SPI serial bus. Each memory device is accessed by a simple serial interface that is SPI bus compatible. The bus signals are SCL, SDI and SDO (see Table 1., page 5 and Figure 7., page 8). The device is selected when the Chip Enable input (E) is held low. All instructions, addresses and data are shifted serially in and out of the chip. The most significant bit is presented first, with the data input (SDI) sampled on the first rising edge of the clock (SCL) after the Chip Enable (E) goes low. The 64 bytes contained in the device can then be accessed sequentially in the following order: 1. Tenths/Hundredths of a Second Register 2. Seconds Register 3. Minutes Register 4. Century/Hours Register 5. Day Register 6. Date Register 7. Month Register 8. Year Register 9. Control Register 10. Watchdog Register 11 - 16.Alarm Registers 17 - 19.Reserved 20. Square Wave Register 21 - 64.User RAM The M41ST95Y/W clock continually monitors VCC for an out-of tolerance condition. Should VCC fall below VPFD, the device terminates an access in progress and resets the device address counter. Inputs to the device will not be recognized at this time to prevent erroneous data from being written to the device from a an out-of-tolerance system. When VCC falls below VSO, the device automati- cally switches over to the battery and powers down into an ultra low current mode of operation to conserve battery life. As system power returns and VCC rises above VSO, the battery is disconnected, and the power supply is switched to external VCC. Write protection continues until VCC reaches VPFD (min) plus tREC (min). For more information on Battery Storage Life refer to Application Note AN1012. SPI Bus Characteristics The Serial Peripheral interface (SPI) bus is intend- ed for synchronous communication between dif- ferent ICs. It consists of four signal lines: Serial Data Input (SDI), Serial Data Output (SDO), Serial Clock (SCL) and a Chip Enable (E). By definition a device that gives out a message is called “transmitter,” the receiving device that gets the message is called “receiver.” The device that controls the message is called “master.” The de- vices that are controlled by the master are called “slaves.” The E input is used to initiate and terminate a data transfer. The SCL input is used to synchronize data transfer between the master (micro) and the slave (M41ST95Y/W) devices. The SCL input, which is generated by the micro- controller, is active only during address and data transfer to any device on the SPI bus (see Figure 7., page 8). The M41ST95Y/W can be driven by a microcon- troller with its SPI peripheral running in either of the two following modes: (CPOL, CPHA) = ('0', '0') or (CPOL, CPHA) = ('1', '1'). For these two modes, input data (SDI) is latched in by the low-to-high transition of clock SCL, and out- put data (SDO) is shifted out on the high-to-low transition of SCL (see Table 2., page 10 and Fig- ure 8., page 10). There is one clock for each bit transferred. Ad- dress and data bits are transferred in groups of eight bits. Due to memory size the second most significant address bit is a Don’t Care (address bit 6). |
Nº de peça semelhante - M41ST95YMX6TR |
|
Descrição semelhante - M41ST95YMX6TR |
|
|
Ligação URL |
Privacy Policy |
ALLDATASHEETPT.COM |
ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |