H27UCG8T2BTR-BC datasheet(44/56 Pages) HYNIX

Nome de Peças	H27UCG8T2BTR-BC

Descrição Electrónicos	64Gb(8192M x 8bit) MLC NAND Flash

Download	56 Pages

Scroll/Zoom	100%

Fabricante Electrônico	HYNIX [Hynix Semiconductor]

Página de início	http://www.skhynix.com/kor/main.do

Logo

44 / 56 page

H27UCG8T2BTR-BC

64Gb(8192M x 8bit) MLC NAND Flash

Rev 0.1 / Oct. 2012

44

4.10. Multi Plane Program

Device supports multiple plane program. It is possible to program in parallel 2 pages, one per each plane.

A multiple plane program cycle consists of a double serial data loading period in which up to 17,664bytes of data

may be loaded into the data register, followed by a non-volatile programming period where the loaded data is

programmed into the appropriate cell. The serial data loading period begins by inputting the Serial Data Input

command (80h), followed by the five cycle address inputs and then serial data for the 1st page. Address for this

page must be within first plane (A<23>=0). The data of first page other than those to be programmed do not

need to be loaded. The device supports random data input exactly like page program operation. The Dummy

Page Program Confirm command (11h) stops 1st page data input and the device becomes busy for a short time

(tDBSY). Once it has become ready again, 81h command must be issued, followed by second page address (5

cycles) and its serial data input. Address for this page must be within second plane (A<23>=1). The data of

second page other than those to be programmed do not need to be loaded. Program Confirm command (10h)

makes parallel programming of both pages start. User can check operation status by R/B# pin or read status

register command, as if it were a normal page program; status register command is also available during Dummy

Busy time (tDBSY). In case of fail in first plane or second plane page program, fail bit of status register will be set:

Pass/Fail status of each plane can be checked by Multi Plane Read Status. Figure 42 details the sequence.

Figure 42 : Multi plane page program

Notes:

1. plane 0 and plane 1 should be selected within the same chip.

2. Only one block should be selected from the each plane.

3. Selected Page address except A23 within two blocks must be same.

4. Any command between 11h and 81h is prohibited except 70h/78h/75h and FFh.

5. Read Status command can be 70h or 78h or 75h.

Nº de peça semelhante - H27UCG8T2BTR-BC

Fabricante Electrônico	Nome de Peças	Folha de dados	Descrição Electrónicos
Hynix Semiconductor	H27UCG8T2B	87Kb / 5P	NAND Flash(SLC,MLC,eMMC,E2NAND3.0,(Solid State Drive))

Fabricante Electrônico	Nome de Peças	Folha de dados	Descrição Electrónicos
List of Unclassifed Man...	S846-SAS	250Kb / 2P	MLC Nand Flash
Hynix Semiconductor	H27UAG8T2B	1Mb / 61P	16Gb (2048M x 8bit) NAND Flash
Toshiba Semiconductor	TH58V128FT	1Mb / 32P	128Mbit (16M x 8bit) CMOS NAND E2PROM
Hynix Semiconductor	H27U1G8F2B	87Kb / 5P	NAND Flash(SLC,MLC,eMMC,E2NAND3.0,(Solid State Drive))
Toshiba Semiconductor	TC5832DC	1Mb / 38P	32 MBIT (4M x 8BIT) CMOS NAND E2PROM
Toshiba Semiconductor	TH58V128DC	1Mb / 32P	128 Mbit (16M x 8bit) CMOS NAND E2PROM (16M BYTE SmartMedia??
WAGO Kontakttechnik Gmb...	752-9400	277Kb / 3P	Edge Computer; 2 x ETHERNET, 4 x USB, HDMI, DP; 4GB RAM; 64GB FLASH
WAGO Kontakttechnik Gmb...	752-9401	277Kb / 3P	Edge Computer; 2 x ETHERNET, 4 x USB, HDMI, DP; 8GB RAM; 64GB FLASH
Samsung semiconductor	K9F6408U0B-TCB0	416Kb / 27P	8M x 8 Bit NAND Flash Memory
Samsung semiconductor	K9F1208U0M-	1Mb / 41P	64M x 8 Bit NAND Flash Memory