LM311 LM211

2

MOTOROLA ANALOG IC DEVICE DATA

Rating

Symbol

LM211

LM311

Unit

Total Supply Voltage

VCC +VEE

36

36

Vdc

Output to Negative Supply Voltage

VO –VEE

50

40

Vdc

Ground to Negative Supply Voltage

VEE

30

30

Vdc

Input Differential Voltage

VID

±30

±30

Vdc

Input Voltage (Note 2)

Vin

±15

±15

Vdc

Voltage at Strobe Pin

–

VCC to VCC–5

VCC to VCC–5

Vdc

Power Dissipation and Thermal Characteristics

Plastic DIP

PD

625

mW

Derate Above TA = +25°C

1/

θJA

5.0

mW/

°C

Operating Ambient Temperature Range

TA

–25 to +85

0 to +70

°C

Operating Junction Temperature

TJ(max)

+150

+150

°C

Storage Temperature Range

Tstg

–65 to +150

–65 to +150

°C

Ch

i i

Sb l

LM211

LM311

Ui

Characteristic

Symbol

Min

Typ

Max

Min

Typ

Max

Unit

Input Offset Voltage (Note 3)

VIO

mV

RS ≤ 50 kΩ, TA = +25°C

–

0.7

3.0

–

2.0

7.5

RS ≤ 50 kΩ, Tlow ≤ TA ≤ Thigh*

–

–

4.0

–

–

10

Input Offset Current (Note 3) TA = +25°C

IIO

–

1.7

10

–

1.7

50

nA

Tlow ≤ TA ≤ Thigh*

–

–

20

–

–

70

Input Bias Current TA = +25°C

IIB

–

45

100

–

45

250

nA

Tlow ≤ TA ≤ Thigh*

–

–

150

–

–

300

Voltage Gain

AV

40

200

–

40

200

–

V/mV

Response Time (Note 4)

–

200

–

–

200

–

ns

Saturation Voltage

VOL

V

VID ≤ –5.0 mV, IO = 50 mA, TA = 25°C

–

0.75

1.5

–

–

–

VID ≤–10 mV, IO = 50 mA, TA = 25°C

–

–

–

–

0.75

1.5

VCC ≥ 4.5 V, VEE = 0, Tlow ≤ TA ≤ Thigh*

VID 6≤6.0 mV, Isink ≤ 8.0 mA

–

0.23

0.4

–

–

–

VID 6≤10 mV, Isink ≤ 8.0 mA

–

–

–

–

0.23

0.4

Strobe ”On” Current (Note 5)

IS

–

3.0

–

–

3.0

–

mA

Output Leakage Current

VID ≥ 5.0 mV, VO= 35 V, TA = 25°C, Istrobe= 3.0 mA

–

0.2

10

–

–

–

nA

VID

≥ 10 mV, VO= 35 V, TA = 25°C, Istrobe= 3.0 mA

–

–

–

–

0.2

50

nA

VID

≥ 5.0 mV, VO= 35 V, Tlow ≤ TA ≤ Thigh*

–

0.1

0.5

–

–

–

µA

Input Voltage Range (Tlow ≤ TA ≤ Thigh*)

VICR

–14.5

–14.7 to

13.8

+13.0

–14.5

–14.7 to

13.8

+13.0

V

Positive Supply Current

ICC

–

+2.4

+6.0

–

+2.4

+7.5

mA

Negative Supply Current

IEE

–

–1.3

–5.0

–

–1.3

–5.0

mA

* Tlow

= –25

°C for LM211

Thigh = +85°C for LM211

= 0

°C for LM311

= +70

°C for LM311

NOTES: 1. Offset voltage, offset current and bias current specifications apply for a supply voltage range from a single 5.0 V supply up to

±15 V supplies.

2. This rating applies for

±15 V supplies. The positive input voltage limit is 30 V above the negative supply. The negative input voltage limit is equal to the

negative supply voltage or 30 V below the positive supply, whichever is less.

3. The offset voltages and offset currents given are the maximum values required to drive the output within a volt of either supply with a 1.0 mA load. Thus,

these parameters define an error band and take into account the ”worst case” effects of voltage gain and input impedance.

4. The response time specified is for a 100 mV input step with 5.0 mV overdrive.

5. Do not short the strobe pin to ground; it should be current driven at 3.0 mA to 5.0 mA.