THIS CATALOG PAGE IS FOR REFERENCE ONLY. REQUEST A

CERTIFIED UMPCO DRAWING FOR ACTUAL SPECIFICATIONS.

ANY CONFLICT BETWEEN THIS DOCUMENT AND THE CERTIFIED

DRAWING, THE CERTIFIED DRAWING WILL TAKE PRECEDENCE.

IF THE DOCUMENT IS CONTROLLED BY ANY OTHER SOURCE

THAN UMPCO, THE CERTIFIED DRAWING MUST BE PURCHASED

THROUGH THAT ORGANIZATION.

CAGE CODE No. 18076

REV

N/C

02/05/09

AS9603

BRACKET,, ANGLE 90°, CRES

UNS S41000, .190 X .375 BOLT

PART NUMBER

7100 LAMPSON AVE * PO BOX 5158 * GARDEN GROVE, CA 92846-5158 SALES: (714) 897-3531 * BUS: (714) 897-3536 * FAX: (714) 897-2611

DIRECTION OF GRAIN

(SEE NOTE 4)

R .510/.490

Ø .210/.200

B

.205

.195

MARK PART

NUMBER AND

MANUFACTURER’S

IDENTIFICATION

PER AS478 CLASS D

.760

.740

A

R .135/.115

MS9603-XXX

.380

.370

.068

.058

95°

85°

.295

.285

R

.510/.490

Ø .395/.385

NOTES:

1.

MATERIAL: CORROSION RESISTANT STEEL PER AMS 5504 (UNS S41000).

2.

HARDNESS: 30-38 HRC.

3.

FINISH: HEAT TREATMENT AND CLEANING IN ACCORDANCE WITH AMS 2550.

4.

GRAIN FLOW SHALL BE PARALLEL WITH ROLLING DIRECTION.

5.

REMOVE BURRS AND BREAK SHARP EDGES .003 -.015, UNLESS OTHERWISE SPECIFIED.

6.

DIMENSIONING AND TOLERANCES PER ANSI Y14.5M-1982 (ASME PUBLICATION)

7.

DIMENSIONS ARE IN INCHES

8.

DO NOT USE UNASSIGNED PART NUMBERS.

9.

APPROXIMATE MASS LB/100 = 1.316 (A+B) + .221

B

.552 - .572

.615 - .635

.678 - .698

.740 - .760

.802 - .822

LENGTH

PART NUMBER

PART NUMBER

PART NUMBER

PART NUMBER

PART NUMBER

0.428 - 0.448

MS9603-005

MS9603-035

MS9603-065

MS9603-095

MS9603-125

0.490 - 0.510

MS9603-006

MS9603-036

MS9603-066

MS9603-096

MS9603-126

0.552 - 0.572

MS9603-007

MS9603-037

MS9603-067

MS9603-097

MS9603-127

0.615 - 0.635

MS9603-008

MS9603-038

MS9603-068

MS9603-098

MS9603-128

0.678 - 0.698

MS9603-009

MS9603-039

MS9603-069

MS9603-099

MS9603-129

0.740 - 0.760

MS9603-010

MS9603-040

MS9603-070

MS9603-100

MS9603-130

0.802 - 0.822

MS9603-011

MS9603-041

MS9603-071

MS9603-101

MS9603-131

0.865 - 0.885

MS9603-012

MS9603-042

MS9603-072

MS9603-102

MS9603-132

0.928 - 0.948

MS9603-013

MS9603-043

MS9603-073

MS9603-103

MS9603-133

0.990 - 1.010

MS9603-014

MS9603-044

MS9603-074

MS9603-104

MS9603-134

1.052 - 1.072

MS9603-015

MS9603-045

MS9603-075

MS9603-105

MS9603-135

1.115 - 1.135

MS9603-016

MS9603-046

MS9603-076

MS9603-106

MS9603-136

1.178 - 1.198

MS9603-017

MS9603-047

MS9603-077

MS9603-107

MS9603-137

1.240 - 1.260

MS9603-018

MS9603-048

MS9603-078

MS9603-108

MS9603-138

1.302 - 1.322

MS9603-019

MS9603-049

MS9603-079

MS9603-109

MS9603-139

1.365 - 1.385

MS9603-020

MS9603-050

MS9603-080

MS9603-110

MS9603-140

1.428 - 1.448

MS9603-021

MS9603-051

MS9603-081

MS9603-111

MS9603-141

1.490 - 1.510

MS9603-022

MS9603-052

MS9603-082

MS9603-112

MS9603-142

TABLE 1 -PART NUMBERS AND DIMENSIONS

A - LENGTH