Os motores de busca de Datasheet de Componentes eletrônicos |
|
LM20CIM7EP Folha de dados(PDF) 5 Page - National Semiconductor (TI) |
|
|
LM20CIM7EP Folha de dados(HTML) 5 Page - National Semiconductor (TI) |
5 / 9 page LM20EP Transfer Function The LM20EP’s transfer function can be described in different ways with varying levels of precision. A simple linear transfer function, with good accuracy near 25˚C, is V O= −11.69 mV/˚C x T + 1.8663 V Over the full operating temperature range of −55˚C to +130˚C, best accuracy can be obtained by using the para- bolic transfer function V O = (−3.88x10 −6xT2) + (−1.15x10−2xT) + 1.8639 solving for T: A linear transfer function can be used over a limited tempera- ture range by calculating a slope and offset that give best results over that range. A linear transfer function can be calculated from the parabolic transfer function of the LM20EP. The slope of the linear transfer function can be calculated using the following equation: m = −7.76 x 10 −6x T − 0.0115, where T is the middle of the temperature range of interest and m is in V/˚C. For example for the temperature range of T min=−30 to Tmax=+100˚C: T=35˚C and m = −11.77 mV/˚C The offset of the linear transfer function can be calculated using the following equation: b=(V OP(Tmax)+VOP(T)+mx(Tmax+T))/2 , where: • V OP(Tmax) is the calculated output voltage at Tmax using the parabolic transfer function for V O • V OP(T) is the calculated output voltage at T using the parabolic transfer function for V O. Using this procedure the best fit linear transfer function for many popular temperature ranges was calculated in Figure 2. As shown in Figure 2 the error that is introduced by the linear transfer function increases with wider temperature ranges. Mounting The LM20EP can be applied easily in the same way as other integrated-circuit temperature sensors. It can be glued or cemented to a surface. The temperature that the LM20EP is sensing will be within about +0.02˚C of the surface tempera- ture to which the LM20EP’s leads are attached to. This presumes that the ambient air temperature is almost the same as the surface temperature; if the air temperature were much higher or lower than the surface temperature, the actual temperature measured would be at an intermediate temperature between the surface temperature and the air temperature. To ensure good thermal conductivity the backside of the LM20EP die is directly attached to the pin 2 GND pin. The tempertures of the lands and traces to the other leads of the LM20EP will also affect the temperature that is being sensed. Alternatively, the LM20EP can be mounted inside a sealed- end metal tube, and can then be dipped into a bath or screwed into a threaded hole in a tank. As with any IC, the LM20EP and accompanying wiring and circuits must be kept insulated and dry, to avoid leakage and corrosion. This is especially true if the circuit may operate at cold temperatures where condensation can occur. Printed-circuit coatings and varnishes such as Humiseal and epoxy paints or dips are often used to ensure that moisture cannot corrode the LM20EP or its connections. The thermal resistance junction to ambient ( θ JA) is the pa- rameter used to calculate the rise of a device junction tem- perature due to its power dissipation. For the LM20EP the equation used to calculate the rise in the die temperature is as follows: T J =TA + θ JA [(V + I Q)+(V + −V O)IL] where I Q is the quiescent current and ILis the load current on the output. Since the LM20EP’s junction temperature is the actual temperature being measured care should be taken to minimize the load current that the LM20EP is required to drive. The tables shown in Figure 3 summarize the rise in die temperature of the LM20EP without any loading, and the thermal resistance for different conditions. Temperature Range Linear Equation V O= Maximum Deviation of Linear Equation from Parabolic Equation (˚C) T min (˚C) T max (˚C) −55 +130 −11.79 mV/˚C x T + 1.8528 V ±1.41 −40 +110 −11.77 mV/˚C x T + 1.8577 V ±0.93 −30 +100 −11.77 mV/˚C x T + 1.8605 V ±0.70 -40 +85 −11.67 mV/˚C x T + 1.8583 V ±0.65 −10 +65 −11.71 mV/˚C x T + 1.8641 V ±0.23 +35 +45 −11.81 mV/˚C x T + 1.8701 V ±0.004 +20 +30 −11.69 mV/˚C x T + 1.8663 V ±0.004 FIGURE 2. First order equations optimized for different temperature ranges. www.national.com 5 |
Nº de peça semelhante - LM20CIM7EP |
|
Descrição semelhante - LM20CIM7EP |
|
|
Ligação URL |
Privacy Policy |
ALLDATASHEETPT.COM |
ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |