Os motores de busca de Datasheet de Componentes eletrônicos |
|
MC145481 Folha de dados(PDF) 5 Page - Motorola, Inc |
|
MC145481 Folha de dados(HTML) 5 Page - Motorola, Inc |
5 / 23 page MC145481 MOTOROLA 5 FUNCTIONAL DESCRIPTION ANALOG INTERFACE AND SIGNAL PATH The transmit portion of this device includes a low–noise, three–terminal op amp capable of driving a 2 k Ω load. This op amp has inputs of TI+ (Pin 19) and TI– (Pin 18) and its output is TG (Pin 17). This op amp is intended to be confi- gured in an inverting gain circuit. The analog signal may be applied directly to the TG pin if this transmit op amp is inde- pendently powered down by connecting the TI+ input to the VDD power supply. The TG pin becomes high impedance when the transmit op amp is powered down. The TG pin is internally connected to a 3–pole anti–aliasing pre–filter. This pre–filter incorporates a 2–pole Butterworth active low–pass filter, followed by a single passive pole. This pre–filter is fol- lowed by a single–ended to differential converter that is clocked at 512 kHz. All subsequent analog processing uti- lizes fully–differential circuitry. The next section is a fully–dif- ferential, 5–pole switched–capacitor low–pass filter with a 3.4 kHz frequency cutoff. After this filter is a 3–pole switched–capacitor high–pass filter having a cutoff fre- quency of about 200 Hz. This high–pass stage has a trans- mission zero at dc that eliminates any dc coming from the analog input or from accumulated op amp offsets in the pre- ceding filter stages. The last stage of the high–pass filter is an autozeroed sample and hold amplifier. One bandgap voltage reference generator and digital–to– analog converter (DAC) are shared by the transmit and re- ceive sections. The autozeroed, switched–capacitor bandgap reference generates precise positive and negative reference voltages that are virtually independent of tempera- ture and power supply voltage. A binary–weighted capacitor array (CDAC) forms the chords of the companding structure, while a resistor string (RDAC) implements the linear steps within each chord. The encode process uses the DAC, the voltage reference, and a frame–by–frame autozeroed comparator to implement a successive–approximation con- version algorithm. All of the analog circuitry involved in the data conversion (the voltage reference, RDAC, CDAC, and comparator) are implemented with a differential architecture. The receive section includes the DAC described above, a sample and hold amplifier, a 5–pole, 3400 Hz switched ca- pacitor low–pass filter with sinX/X correction, and a 2–pole active smoothing filter to reduce the spectral components of the switched capacitor filter. The output of the smoothing fil- ter is buffered by an amplifier, which is output at the RO– pin. This output is capable of driving a 2 k Ω load to the VAG pin. The MC145481 also has a pair of power amplifiers that are connected in a push–pull configuration. The PI pin is the in- verting input to the PO– power amplifier. The non–inverting input is internally tied to the VAG pin. This allows this amplifier to be used in an inverting gain circuit with two external resis- tors. The PO+ amplifier has a gain of minus one, and is in- ternally connected to the PO– output. This complete power amplifier circuit is a differential (push–pull) amplifier with ad- justable gain that is capable of driving a 300 Ω load to +7 dBm. The power amplifier may be powered down inde- pendently of the rest of the chip by connecting the PI pin to VDD. POWER–DOWN There are two methods of putting this device into a low power consumption mode, which makes the device nonfunc- tional and consumes virtually no power. PDI is the power– down input pin which, when taken low, powers down the device. Another way to power the device down is to hold both the FST and FSR pins low while the BCLKT and MCLK pins are clocked. When the chip is powered down, the VAG, TG, RO–, PO+, PO–, and DT outputs are high impedance and the VAG Ref pin is pulled to the VDD power supply with a non– linear, high–impedance circuit. To return the chip to the pow- er–up state, PDI must be high and the FST frame sync pulse must be present while the BCLKT and MCLK pins are clocked. The DT output will remain in a high–impedance state for at least two 8 kHz FST pulses after power–up. MASTER CLOCK Since this codec–filter design has a single DAC architec- ture, the MCLK pin is used as the master clock for all analog signal processing including analog–to–digital conversion, digital–to–analog conversion, and for transmit and receive fil- tering functions of this device. The clock frequency applied to the MCLK pin may be 256 kHz, 512 kHz, 1.536 MHz, 1.544 MHz, 2.048 MHz, 2.56 MHz, or 4.096 MHz. This de- vice has a prescaler that automatically determines the proper divide ratio to use for the MCLK input, which achieves the re- quired 256 kHz internal sequencing clock. The clocking re- quirements of the MCLK input are independent of the PCM data transfer mode (i.e., Long Frame Sync, Short Frame Sync, IDL mode, or GCI mode). DIGITAL I/O The MC145481 is pin selectable for Mu–Law or A–Law. Table 1 shows the 8–bit data word format for positive and negative zero and full scale for both companding schemes. Table 2 shows the series of eight PCM words for both Mu– Law and A–Law that correspond to a digital milliwatt. The digital mW is the 1 kHz calibration signal reconstructed by the DAC that defines the absolute gain or 0 dBm0 Transmis- sion Level Point (TLP) of the DAC. The timing for the PCM data transfer is independent of the companding scheme se- lected. Refer to Figure 2 for a summary and comparison of the four PCM data interface modes of this device. |
Nº de peça semelhante - MC145481 |
|
Descrição semelhante - MC145481 |
|
|
Ligação URL |
Privacy Policy |
ALLDATASHEETPT.COM |
ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |