Os motores de busca de Datasheet de Componentes eletrônicos |
|
MC33035P Folha de dados(PDF) 8 Page - ON Semiconductor |
|
MC33035P Folha de dados(HTML) 8 Page - ON Semiconductor |
8 / 28 page MC33035, NCV33035 http://onsemi.com 8 PIN FUNCTION DESCRIPTION Pin Symbol Description 1, 2, 24 BT, AT, CT These three open collector Top Drive outputs are designed to drive the external upper power switch transistors. 3 Fwd/Rev The Forward/Reverse Input is used to change the direction of motor rotation. 4, 5, 6 SA, SB, SC These three Sensor Inputs control the commutation sequence. 7 Output Enable A logic high at this input causes the motor to run, while a low causes it to coast. 8 Reference Output This output provides charging current for the oscillator timing capacitor CT and a reference for the error amplifier. It may also serve to furnish sensor power. 9 Current Sense Noninverting Input A 100 mV signal, with respect to Pin 15, at this input terminates output switch conduction during a given oscillator cycle. This pin normally connects to the top side of the current sense resistor. 10 Oscillator The Oscillator frequency is programmed by the values selected for the timing components, RT and CT. 11 Error Amp Noninverting Input This input is normally connected to the speed set potentiometer. 12 Error Amp Inverting Input This input is normally connected to the Error Amp Output in open loop applications. 13 Error Amp Out/PWM Input This pin is available for compensation in closed loop applications. 14 Fault Output This open collector output is active low during one or more of the following conditions: Invalid Sensor Input code, Enable Input at logic 0, Current Sense Input greater than 100 mV (Pin 9 with respect to Pin 15), Undervoltage Lockout activation, and Thermal Shutdown. 15 Current Sense Inverting Input Reference pin for internal 100 mV threshold. This pin is normally connected to the bottom side of the current sense resistor. 16 Gnd This pin supplies a ground for the control circuit and should be referenced back to the power source ground. 17 VCC This pin is the positive supply of the control IC. The controller is functional over a minimum VCC range of 10 to 30 V. 18 VC The high state (VOH) of the Bottom Drive Outputs is set by the voltage applied to this pin. The controller is operational over a minimum VC range of 10 to 30 V. 19, 20, 21 CB, BB, AB These three totem pole Bottom Drive Outputs are designed for direct drive of the external bottom power switch transistors. 22 60 °/120° Select The electrical state of this pin configures the control circuit operation for either 60 ° (high state) or 120° (low state) sensor electrical phasing inputs. 23 Brake A logic low state at this input allows the motor to run, while a high state does not allow motor operation and if operating causes rapid deceleration. |
Nº de peça semelhante - MC33035P |
|
Descrição semelhante - MC33035P |
|
|
Ligação URL |
Privacy Policy |
ALLDATASHEETPT.COM |
ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |