Os motores de busca de Datasheet de Componentes eletrônicos |
|
M74HC4538B1R Folha de dados(PDF) 3 Page - STMicroelectronics |
|
M74HC4538B1R Folha de dados(HTML) 3 Page - STMicroelectronics |
3 / 14 page BLOCK DIAGRAM Notes : 1. Cx, Rx, Dx are external components. 2. Dx is a clamping diode. 3. The external capacitor is charged to VCC in the stand-by state, i.e. no trigger. When the supply voltage is turned off Cx is discharged mainlythrough an internal parasitic diode (see figures). IfCx is sufficiently largeand VCC decreases rapidy, there willbesome possibility of damaging the I.C. with a surge current or latch-up. If the voltage supply filter capacitor is large enough and VCC decrease slowly, the surge current is automatically limited and damage the I.C. is avoided. The maximum forward current of the parasitic diode is ap- proximately 20 mA. In cases where Cx is large the time taken for the supply voltage to fall to 0.4 VCC can be calculated as follows : tf ≥ (VCC – 0.7) ⋅ Cx/20 mA In cases where tf is too short an external champing diode is required to protect the I.C. from the surge current. FUNCTIONAL DESCRIPTION STAND-BY STATE The external capacitor, Cx, is fully charged to VCC in the stand-by state. Hence, before triggering, tran- sistor Qp and Qn (connected to the Rx/Cx node) are both turned off. The two comparators that control the timing and the two reference voltage sources stop operating. The total supply current is therefore only leakage current. TRIGGER OPERATION Triggering occurs when : 1 st) A is ”low” and B has a falling edge ; 2 nd) B is ”high” and A has a rising edge ; After the multivibrator has been retriggered com- parator C1 and C2 start operating and Qn is turned on. Cx then discharges through Qn. The voltage at the node Rx/Cx external falls. When it reaches VREFL the output of comparator C1 becomes low. This in turn resets the flip-flop and Qn is turned off. At this point C1 stops functioning but C2 continues to operate. The voltage at R/C external begins to rise with a time constant set by the external components Rx, Cx. Triggering the multivibrator causes Q to go high after internal delay due to the flip-flop and the gate. Q re- mains high until the voltage at R/C external rises again to VREFH. At this point C2 output goes low and G goes low. C2 stops operating. That means that after triggering when the voltage at R/C external re- turns to VREFH the multivibrator has returned to its MONOSTABLE STATE. In the case where Rx • Cx are large enough and the discharge time of the ca- pacitor and the delay time in the I.C. can be ignored, the width of the output pulse tw (out) is as follows : tW(OUT) = 0.72 Cx • Rx RE-TRIGGER OPERATION When a second trigger pulse follows the first its ef- fect will depend on the state of the multivibrator. If the capacitor Cx is being charged the voltage level of Rx/Cx external falls to VREFL again and Q remains high i.e. the retrigger pulse arrives in a time shorter than the period Rx • Cx seconds, the capacitor charging time constant. If the second trigger pulse is very close to the initial trigger pulse it is ineffective ; i.e., the second trigger must arrive in the capacitor discharge cycle to be ineffective. Hence the minimum time for a second trigger to be effective, trr (Min.) depends on VCC and Cx. M54/ M74HC4538 3/14 |
Nº de peça semelhante - M74HC4538B1R |
|
Descrição semelhante - M74HC4538B1R |
|
|
Ligação URL |
Privacy Policy |
ALLDATASHEETPT.COM |
ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |