Os motores de busca de Datasheet de Componentes eletrônicos |
|
5V40501DVGI Folha de dados(PDF) 3 Page - Integrated Device Technology |
|
5V40501DVGI Folha de dados(HTML) 3 Page - Integrated Device Technology |
3 / 9 page IDT5V40501 LOCO™ PLL CLOCK MULTIPLIER CLOCK MULTIPLIER IDT™ LOCO™ PLL CLOCK MULTIPLIER 3 IDT5V40501 REV C 102808 External Components Decoupling Capacitor As with any high-performance mixed-signal IC, the IDT5V40501 must be isolated from system power supply noise to perform optimally. A decoupling capacitor of 0.01µF must be connected between VDD and the GND. It must be connected close to the IDT5V40501 to minimize lead inductance. No external power supply filtering is required for the IDT5V40501. Series Termination Resistor A 33 Ω terminating resistor can be used next to the CLK pin for trace lengths over one inch. Crystal Load Capacitors The total on-chip capacitance is approximately 12 pF. A parallel resonant, fundamental mode crystal should be used. The device crystal connections should include pads for small capacitors from X1 to ground and from X2 to ground. These capacitors are used to adjust the stray capacitance of the board to match the nominally required crystal load capacitance. Because load capacitance can only be increased in this trimming process, it is important to keep stray capacitance to a minimum by using very short PCB traces (and no vias) between the crystal and device. Crystal capacitors, if needed, must be connected from each of the pins X1 and X2 to ground. The value (in pF) of these crystal caps should equal (CL -12 pF)*2. In this equation, CL= crystal load capacitance in pF. Example: For a crystal with a 16 pF load capacitance, each crystal capacitor would be 8 pF [(16-12) x 2 = 8]. Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the IDT5V40501. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the device at these or any other conditions above those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can affect product reliability. Electrical parameters are guaranteed only over the recommended operating temperature range. Recommended Operation Conditions Item Rating Supply Voltage, VDD 7 V All Inputs and Outputs -0.5 V to VDD+0.5 V Ambient Operating Temperature -40 to +85 ° C Storage Temperature -65 to +150 ° C Soldering Temperature 260 ° C Parameter Min. Typ. Max. Units Ambient Operating Temperature (commercial) 0 +70 ° C Ambient Operating Temperature (industrial) -40 85 ° C Power Supply Voltage (measured in respect to GND) +3.135 3.3 +3.465 V |
Nº de peça semelhante - 5V40501DVGI |
|
Descrição semelhante - 5V40501DVGI |
|
|
Ligação URL |
Privacy Policy |
ALLDATASHEETPT.COM |
ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |