Os motores de busca de Datasheet de Componentes eletrônicos |
|
D-436-52 Folha de dados(PDF) 2 Page - PANDUIT CORP. |
|
D-436-52 Folha de dados(HTML) 2 Page - PANDUIT CORP. |
2 / 2 page SPECIFICATION CONTROL DRAWING TE Connectivity 305 Constitution Drive Menlo Park, CA 94025, USA Raychem Products TITLE : IN-LINE SPLICE SEALING SYSTEM, 2 OR 3 TO 1 SPLICE: Tin Plated, Color Coded, with Inspection Slots UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN MILLIMETERS. INCHES DIMENSIONS ARE BETWEEN BRACKETS. DOCUMENT NO.: D-436-52/-53 TOLERANCES: 0.00 N/A 0.0 N/A 0 N/A ANGLES: N/A ROUGHNESS IN MICRON TE Connectivity reserves the right to amend this drawing at any time. Users should evaluate the suitability of the product for their application. DATE: 15-Apr-11 DOC ISSUE: 2 DRAWN BY: M. FORONDA REPLACES: N/A DCR NUMBER: D001302 PROD. REV. SEE TABLE SCALE: None SIZE: A SHEET: 2 of 2 Print Date: 9-May-11 If this document is printed it becomes uncontrolled. Check for the latest revision. APPLICATION 1. These parts are designed to provide an immersion resistant in-line splices of 2 or 3 to 1 wires falling within the size range listed on sheet 1, having insulations rated for at least 135C. 2. Parts are available only as an assembly of one of each Item #1 and Item #2. 3. Parts are to be installed per Thermofit Assembly Procedure, see below. 4. Inside diameter and outside diameter of splice are to be measured in crimp areas, 2.54 to 5.08 (0.100 to 0.200) from ends of part. Slight burr permitted on parted surfaces. 5. Acceptance sampling shall be in accordance with Paragraph 4.6.1 of MIL-T-7928. 6 . Packing and packaging shall be in accordance with Section 5, Level C, of MIL-T-7928. 7. This document takes precedence over documents referenced herein. THERMOFIT ASSEMBLY PROCEDURE 1.0 SCOPE This document outlines the procedure to be followed to obtain immersion resistant 3 or 2 to 1 in-line splices using Thermofit In-Line Splice Sealing System D-436-52/-53. 2.0 PROCEDURE: a) Strip all wires 7.92 (0.312) to 8.74 (0.344). b) Attach the single lead to the appropriate size crimp splice using a Raychem AD-1377 Crimp Tool. c) Pass the wires to be attached to other barrel through the sealing sleeve from the three-hole insert end. d) Insert wires into barrel and crimp. Care must be taken that the wires remain untwisted between the crimp splice and the three wire seal or the sealing sleeve cannot be positioned properly. e) Apply heat, using the recommended heat source, first to the three-hole insert and then the other. Heat should be applied until insert melts and flows axially along the wires. 3.0 RECOMMENDED RAYCHEM HEATING TOOLS Heater Reflector Thermogun #500A TG-14 Shop Air Heater #CV-4504 991180 Mini-Gun #CV-5300 991319 |
Nº de peça semelhante - D-436-52 |
|
Descrição semelhante - D-436-52 |
|
|
Ligação URL |
Privacy Policy |
ALLDATASHEETPT.COM |
ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |