Os motores de busca de Datasheet de Componentes eletrônicos |
|
GS-12-452 Folha de dados(PDF) 4 Page - FCI connector |
|
GS-12-452 Folha de dados(HTML) 4 Page - FCI connector |
4 / 13 page NUMBER GS-12-452 TYPE PRODUCT SPECIFCATION TITLE PAGE REVISION 4 of 13 C AUTHORIZED BY DATE ZipLineTM Connector System M. Gray 2009-10-05 CLASSIFICATION UNRESTRICTED Copyright FCI Form E-3334 Rev F GS-01-001 5.0 ELECTRICAL CHARACTERISTICS 5.1 Contact Resistance 5.1.1 Low Level (LLCR) Measurements shall be performed using a four-wire method per EIA 364-23. The maximum initial contact resistance is 150 m Ω for backpanel and orthogonal configurations, and 255 mΩ for coplanar configurations. The increase in resistance for any position shall not exceed 10 m Ω. Make sure metal organizer has been removed for all signal contact measurements because several positions are shorted together by the organizer. The following details apply: a. Test voltage: 20 mV maximum open circuit b. Test current: 100 mA maximum c. Number of readings: 500 minimum 5.1.2 At Specified Current (power contacts only) The contact resistance at a specified current shall not exceed 5.00mΩ initially or after mating cycles and environmental exposure when measured in accordance with EIA 364-06. The test current is as follows: 1 Column Fully Powered 6.00A 2 Adjacent Columns Fully Powered 4.50A All Columns Fully Powered 2.25A The metal organizer is to remain assembled for power contact evaluation. There is no shorting between power contacts and the metal organizer. 5.2 Insulation Resistance The insulation resistance of mated connectors shall not be less than 1000 M Ω after environmental exposure when measured in accordance with EIA 364-21. Make sure metal organizer has been removed for all signal contact measurements because several positions are shorted together by the organizer. The following details shall apply: a. Test voltage: 500 VDC b. Electrification time: 60 seconds c. Points of measurement: between closest adjacent contacts d. Number of readings: 30 (10 readings per loose-piece connector set) 5.3 Dielectric Withstanding Voltage There shall be no evidence of arc-over, insulation breakdown, or excessive leakage current (> 0.5 mA) when the mated connectors are tested in accordance with EIA 364-20. Make sure metal organizer has been removed for all signal contact measurements because several positions are shorted together by the organizer. The following details shall apply: a. Test voltage: 500 VAC, 60Hz b. Test duration: 60 seconds c. Voltage application rate: 500 V per second d. Points of Measurement: between closest adjacent contacts e. Number of readings: 30 (10 readings per loose-piece connector set) PDM: Rev:C Released . STATUS: Printed: Nov 28, 2010 |
Nº de peça semelhante - GS-12-452 |
|
Descrição semelhante - GS-12-452 |
|
|
Ligação URL |
Privacy Policy |
ALLDATASHEETPT.COM |
ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |