Os motores de busca de Datasheet de Componentes eletrônicos
Selected language  

  Portuguese  ▼

nome da peças
         descrição  


CAT5112_04 Datasheet(Folha de dados) 2 Page - Catalyst Semiconductor

Nome de Peças. CAT5112_04
descrição  32-Tap Digitally Programmable Potentiometer
Download  7 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Fbricantes  CATALYST [Catalyst Semiconductor]
Página de início  http://www.catalyst-semiconductor.com
Logo 

   
 2 page
background image
CAT5112
2
Doc. No. 2002, Rev. L
of the CAT5112 and is active low. When in a high
state, activity on the
INC and U/D inputs will not
affect or change the position of the wiper.
DEVICE OPERATION
The CAT5112 operates like a digitally controlled
potentiometer with RH and RL equivalent to the high
and low terminals and RWB equivalent to the mechanical
potentiometer's wiper. There are 32 available tap posi-
tions including the resistor end points, RH and RL. There
are 31 resistor elements connected in series between
the RH and RL terminals. The wiper terminal is
connected to one of the 32 taps and controlled by three
inputs,
INC, U/D and CS. These inputs control a five-bit
up/down counter whose output is decoded to select the
wiper position. The selected wiper position can be
stored in nonvolatile memory using the
INC and
CS inputs.
With
CS set LOW the CAT5112 is selected and will
respond to the U/
D and INC inputs. HIGH to LOW
transitions on
INC wil increment or decrement the
wiper (depending on the state of the U/
D input and five-
bit counter). The wiper, when at either fixed terminal,
acts like its mechanical equivalent and does not move
beyond the last position. The value of the counter is
stored in nonvolatile memory whenever
CS transitions
HIGH while the
INC input is also HIGH. When the
CAT5112 is powered-down, the last stored wiper counter
position is maintained in the nonvolatile memory. When
power is restored, the contents of the memory are
recalled and the counter is set to the value stored.
With
INC set low, the CAT5112 may be de-selected
and powered down without storing the current wiper
position in nonvolatile memory. This allows the
system to always power up to a preset value stored
in nonvolatile memory.
PIN DESCRIPTIONS
INC
INC
INC
INC
INC: Increment Control Input
The
INC input (on the falling edge) moves the wiper in the
up or down direction determined by the condition of the
U/
D input.
U/
D
D
D
D
D: Up/Down Control Input
The U/
D input controls the direction of the wiper
movement. When in a high state and
CS is low, any high-
to-low transition on
INC will cause the wiper to move one
increment toward the RH terminal. When in a low state
and
CS is low, any high-to-low transition on INC will
cause the wiper to move one increment towards the
RL terminal.
RH: High End Potentiometer Terminal
RH is the high end terminal of the potentiometer. It is not
required that this terminal be connected to a potential
greater than the RL terminal. Voltage applied to the RH
terminal cannot exceed the supply voltage, VCC or go
below ground, GND.
RWB: Wiper Potentiometer Terminal (Buffered)
RWB is the buffered wiper terminal of the potentiometer. Its
position on the resistor array is controlled by the control
inputs,
INC, U/D and CS.
RL: Low End Potentiometer Terminal
RL is the low end terminal of the potentiometer. It is not
required that this terminal be connected to a potential
less than the RH terminal. Voltage applied to the RL
terminal cannot exceed the supply voltage, VCC or go
below ground, GND. RL and RH are electrically
interchangeable.
CS
CS
CS
CS
CS: Chip Select
The chip select input is used to activate the control input
PIN FUNCTIONS
Pin Name
Function
INC
Increment Control
U/
D
Up/Down Control
RH
Potentiometer High Terminal
GND
Ground
RWB
Buffered Wiper Terminal
RL
Potentiometer Low Terminal
CS
Chip Select
VCC
Supply Voltage
PIN CONFIGURATION
PDIP Package (P, L)
TSSOP Package (U, Y)
MSOP Package (R, Z)
INC
VCC
CS
RL
RWB
U
/D
RH
GND
1
2
3
4
8
7
6
5
CS
INC
VCC
RL
RWB
U
/D
RH
GND
1
2
3
4
8
7
6
5
VCC
RL
RWB
GND
RH
INC
U/
D
CS
1
2
3
4
8
7
6
5
CS
INC
VCC
RL
RWB
U
/D
RH
GND
1
2
3
4
8
7
6
5
SOIC Package (S, V)




Html Pages

1  2  3  4  5  6  7 


Datasheet Download



Descrição relacionada

número de peçaDetalhesHtml ViewFabricantes
CAT512732-Tap Digitally Programmable Potentiometer DPP TM 1 2 3 4 5 MoreCatalyst Semiconductor
CAT512332-Tap MiniPot TM Digitally Programmable Potentiometers with 2-Wire Interface 1 2 3 4 5 MoreCatalyst Semiconductor
CAT5126One-Time Digitally Programmable 32 Tap Potentiometer 1 2 3 4 5 MoreCatalyst Semiconductor
CAT521_04Configured Digitally Programmable Potentiometer 1 2 3 4 5 MoreCatalyst Semiconductor
CAT522_04Configured Digitally Programmable Potentiometer 1 2 3 4 5 MoreCatalyst Semiconductor
CAT523_04Configured Digitally Programmable Potentiometer 1 2 3 4 5 MoreCatalyst Semiconductor
CAT524_04Configured Digitally Programmable Potentiometer 1 2 3 4 5 MoreCatalyst Semiconductor
CAT525_04Configured Digitally Programmable Potentiometer 1 2 3 4 5 MoreCatalyst Semiconductor
A3985Digitally Programmable Dual Full-Bridge MOSFET Driver 1 2 3 4 5 MoreAllegro MicroSystems
WIW1028Trimmer Potentiometer 1 List of Unclassifed Manufacturers

Ligação URL

ALLDATASHEET é util para você?  [ DONATE ]  

Sobre Alldatasheet   |  Publicidade   |   Contato conosco    |   Política de Privacidade   |   Favoritos   |  Troca de Link    |  Lista de Fabricantes
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  , Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp  |   Russian : Alldatasheetru.com
Korean : Alldatasheet.co.kr   |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com  |   Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl