Os motores de busca de Datasheet de Componentes eletrônicos
  Portuguese  ▼
ALLDATASHEETPT.COM

X  

ST95P08M6TR Folha de dados(PDF) 7 Page - STMicroelectronics

Nome de Peças ST95P08M6TR
Descrição Electrónicos  8 Kbit Serial SPI EEPROM with Positive Clock Strobe
Download  16 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricante Electrônico  STMICROELECTRONICS [STMicroelectronics]
Página de início  http://www.st.com
Logo STMICROELECTRONICS - STMicroelectronics

ST95P08M6TR Folha de dados(HTML) 7 Page - STMicroelectronics

Back Button ST95P08M6TR Datasheet HTML 3Page - STMicroelectronics ST95P08M6TR Datasheet HTML 4Page - STMicroelectronics ST95P08M6TR Datasheet HTML 5Page - STMicroelectronics ST95P08M6TR Datasheet HTML 6Page - STMicroelectronics ST95P08M6TR Datasheet HTML 7Page - STMicroelectronics ST95P08M6TR Datasheet HTML 8Page - STMicroelectronics ST95P08M6TR Datasheet HTML 9Page - STMicroelectronics ST95P08M6TR Datasheet HTML 10Page - STMicroelectronics ST95P08M6TR Datasheet HTML 11Page - STMicroelectronics Next Button
Zoom Inzoom in Zoom Outzoom out
 7 / 16 page
background image
C
Q
AI01072B
S
D
HOLD
tCLHX
tHXCH
tHXCH
tCLHX
tHHQX
tHLQZ
Figure 7. Hold Timing
Write Protect (W). This pin is for hardware write
protect. When W is low, non-volatile writes to the
ST95P08 are disabled but any other operation
stays enabled. When W is high, all operations
including non-volatile writes are available. W going
low at any time before the last bit D0 of the data
stream will reset the write enable latch and prevent
programming. No action on W or on the write
enable latch can interrupt a write cycle which has
commenced.
Hold (HOLD). The HOLD pin is used to pause
serial communications with a ST95P08 without
resetting the serial sequence. To take the Hold
condition into account, the product must be se-
lected (S = 0). Then the Hold state is validated by
a high to low transition on HOLD when C is low. To
resume the communications, HOLDis brought high
when C is low. During Hold condition D, Q, and C
are at a high impedance state.
When the ST95P08 is under Hold condition, it is
possible to deselect it. However, the serial commu-
nications will remain paused after a reselect, and
the chip will be reset.
OPERATIONS
All instructions, addresses and data are shifted in
and out of the chip MSB first. Data input (D) is
sampled on the first rising edge of clock (C) after
the chip select (S) goes low. Prior to any operation,
a one-byte instruction code must be entered in the
chip. This code is entered via the data input (D),
and latched on the rising edge of the clock input
(C). To enter an instruction code, the product must
have been previously selected (S = low). Table 7
shows the instruction set and format for device
operation. When an invalid instruction is sent (one
not contained in Table 7), the chip is automatically
deselected. For operations that read or write data
in the memory array, bit 3 of the instruction is the
MSB of the address, otherwise, it is a don’t care.
Write Enable (WREN) and Write Disable (WRDI)
The ST95P08 contains a write enable latch. This
latch must be set prior to every WRITE or WRSR
operation. The WREN instruction will set the latch
and the WRDI instruction will reset the latch. The
latch is reset under all the following conditions:
– W pin is low
– Power on
– WRDI instruction executed
– WRSR instruction executed
– WRITE instruction executed
As soon as the WREN or WRDI instruction is
received by the ST95P08, the circuit executes the
instruction and enters a wait mode until it is dese-
lected.
7/16
ST95P08


Nº de peça semelhante - ST95P08M6TR

Fabricante ElectrônicoNome de PeçasFolha de dadosDescrição Electrónicos
logo
STMicroelectronics
ST95P08M6TR STMICROELECTRONICS-ST95P08M6TR Datasheet
151Kb / 16P
   SERIAL ACCESS SPI BUS 2K 256 x 8 EEPROM
More results

Descrição semelhante - ST95P08M6TR

Fabricante ElectrônicoNome de PeçasFolha de dadosDescrição Electrónicos
logo
STMicroelectronics
ST95040 STMICROELECTRONICS-ST95040 Datasheet
110Kb / 18P
   4K/2K/1K Serial SPI EEPROM with Positive Clock Strobe
M95080-WMN6TP STMICROELECTRONICS-M95080-WMN6TP Datasheet
350Kb / 42P
   8-Kbit serial SPI bus EEPROM with high-speed clock
M95080-WMN6P STMICROELECTRONICS-M95080-WMN6P Datasheet
781Kb / 4P
   8-Kbit serial SPI bus EEPROM with high-speed clock
M95160 STMICROELECTRONICS-M95160_08 Datasheet
394Kb / 45P
   16 Kbit and 8 Kbit serial SPI bus EEPROM with high speed clock
M95160-X STMICROELECTRONICS-M95160-X Datasheet
436Kb / 50P
   16 Kbit and 8 Kbit serial SPI bus EEPROM with high speed clock
M95160 STMICROELECTRONICS-M95160 Datasheet
405Kb / 45P
   16 Kbit and 8 Kbit serial SPI bus EEPROM with high speed clock
ST95022 STMICROELECTRONICS-ST95022 Datasheet
113Kb / 16P
   2 Kbit Serial SPI EEPROM with High Speed Clock
M95320-W STMICROELECTRONICS-M95320-W Datasheet
412Kb / 48P
   32-Kbit serial SPI bus EEPROM with high-speed clock
M95256 STMICROELECTRONICS-M95256 Datasheet
345Kb / 39P
   256 Kbit Serial SPI bus EEPROM with high speed clock
M95512-DR STMICROELECTRONICS-M95512-DR Datasheet
483Kb / 48P
   512 Kbit serial SPI bus EEPROM with high-speed clock
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16


Folha de dados Download

Go To PDF Page


Ligação URL




Privacy Policy
ALLDATASHEETPT.COM
ALLDATASHEET é útil para você?  [ DONATE ] 

Sobre Alldatasheet   |   Publicidade   |   Contato conosco   |   Privacy Policy   |   roca de Link   |   Lista de Fabricantes
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com