SN54ALVTH32373, SN74ALVTH32373

2.5-V/3.3-V 32-BIT TRANSPARENT D-TYPE LATCHES

WITH 3-STATE OUTPUTS

SCES322A – FEBRUARY 2000 – REVISED APRIL 2000

5

POST OFFICE BOX 655303

electrical characteristics over recommended operating free-air temperature range,

PARAMETER

TEST CONDITIONS

SN54ALVTH32373

SN74ALVTH32373

UNIT

PARAMETER

TEST CONDITIONS

MIN

TYP†

MAX

MIN

TYP†

MAX

UNIT

VIK

VCC = 2.3 V,

II = –18 mA

–1.2

–1.2

V

VCC = 2.3 V to 2.7 V,

IOH = –100 µA

VCC–0.2

VCC–0.2

VOH

VCC =2 3V

IOH = –6 mA

1.8

V

VCC = 2.3 V

IOH = –8 mA

1.8

VCC = 2.3 V to 2.7 V,

IOL = 100 µA

0.2

0.2

IOL = 6 mA

0.4

VOL

VCC =2 3V

IOL = 8 mA

0.4

V

VCC = 2.3 V

IOL = 18 mA

0.5

IOL = 24 mA

0.5

Control inputs

VCC = 2.7 V,

VI = VCC or GND

±1

±1

Control inputs

VCC = 0 or 2.7 V,

VI = 5.5 V

10

10

II

VI = 5.5 V

10

10

µA

Data inputs

VCC = 2.7 V

VI = VCC

1

1

VI = 0

–5

–5

Ioff

VCC = 0,

VI or VO = 0 to 4.5 V

±100

µA

IBHL‡

VCC = 2.3 V,

VI = 0.7 V

115*

115

µA

IBHH§

VCC = 2.3 V,

VI = 1.7 V

–10*

–10

µA

IBHLO¶

VCC = 2.7 V,

VI = 0 to VCC

300*

300

µA

IBHHO#

VCC = 2.7 V,

VI = 0 to VCC

–300*

–300

µA

IEX||

VCC = 2.3 V,

VO = 5.5 V

125

125

µA

IOZ(PU/PD)k

VCC ≤ 1.2 V, VO = 0.5 V to VCC,

VI = GND or VCC, OE = don’t care

±100

±100

µA

IOZH

VCC = 2.7 V

VO = 2.3 V,

VI = 0.7 V or 1.7 V

5

5

µA

IOZL

VCC = 2.7 V

VO = 0.5 V,

VI = 0.7 V or 1.7 V

–5

–5

µA

VCC = 2.7 V,

Outputs high

0.04

0.1

0.04

0.1

ICC

VCC = 2.7 V,

IO = 0,

Outputs low

2.3

4.5

2.3

4.5

mA

VI = VCC or GND

Outputs disabled

0.04

0.1

0.04

0.1

Ci

VCC = 2.5 V,

VI = 2.5 V or 0

3.5

3.5

pF

Co

VCC = 2.5 V,

VO = 2.5 V or 0

6

6

pF

* On products compliant to MIL-PRF-38535, this parameter is not production tested.

† All typical values are at VCC = 2.5 V, TA = 25°C.

‡ The bus-hold circuit can sink at least the minimum low sustaining current at VIL max. IBHL should be measured after lowering VIN to GND and

then raising it to VIL max.

§ The bus-hold circuit can source at least the minimum high sustaining current at VIH min. IBHH should be measured after raising VIN to VCC and

then lowering it to VIH min.

¶ An external driver must source at least IBHLO to switch this node from low to high.

# An external driver must sink at least IBHHO to switch this node from high to low.

|| Current into an output in the high state when VO > VCC

PRODUCT PREVIEW information concerns products in the formative or

design phase of development. Characteristic data and other

specifications are design goals. Texas Instruments reserves the right to

change or discontinue these products without notice.