![]() |
Os motores de busca de Datasheet de Componentes eletrônicos |
|
FM31L276-GTR Folha de dados(PDF) 5 Page - Ramtron International Corporation |
|
FM31L276-GTR Folha de dados(HTML) 5 Page - Ramtron International Corporation |
5 / 25 page ![]() FM31L278/L276/L274/L272 - 3V I2C Companion Rev. 3.0 Feb. 2009 Page 5 of 25 VTP VTP 2.6V 0 2.9V 1 The watchdog timer can also be used to assert the reset signal (/RST). The watchdog is a free running programmable timer. The period can be software programmed from 100 ms to 3 seconds in 100 ms increments via a 5-bit nonvolatile register. All programmed settings are minimum values and vary with temperature according to the operating specifications. The watchdog has two additional controls associated with its operation, a watchdog enable bit (WDE) and timer restart bits (WR). Both the enable bit must be set and the watchdog must timeout in order to drive /RST active. If a reset event occurs, the timer will automatically restart on the rising edge of the reset pulse. If WDE=0, the watchdog timer runs but a watchdog fault will not cause /RST to be asserted low. The WTR flag will be set, indicating a watchdog fault. This setting is useful during software development and the developer does not want /RST to drive. Note that setting the maximum timeout setting (11111b) disables the counter to save power. The second control is a nibble that restarts the timer preventing a reset. The timer should be restarted after changing the timeout value. The watchdog timeout value is located in register 0Ah, bits 4-0, and the watchdog enable is bit 7. The watchdog is restarted by writing the pattern 1010b to the lower nibble of register 09h. Writing this pattern will also cause the timer to load new timeout values. Writing other patterns to this address will not affect its operation. Note the watchdog timer is free- running. Prior to enabling it, users should restart the timer as described above. This assures that the full timeout period will be set immediately after enabling. The watchdog is disabled when VDD is below VTP. The following table summarizes the watchdog bits. A block diagram follows. Watchdog timeout WDT4-0 0Ah, bits 4-0 Watchdog enable WDE 0Ah, bit 7 Watchdog restart WR3-0 09h, bits 3-0 Figure 3. Watchdog Timer Manual Reset The /RST pin is bi-directional and allows the FM31L27x to filter and de-bounce a manual reset switch. The /RST input detects an external low condition and responds by driving the /RST signal low for 100 ms. Figure 4. Manual Reset Note that an internal weak pull-up on /RST eliminates the need for additional external components. Reset Flags In case of a reset condition, a flag will be set to indicate the source of the reset. A low VDD reset or manual reset is indicated by the POR flag, register 09h bit 6. A watchdog reset is indicated by the WTR flag, register 09h bit 7. Note that the flags are internally set in response to reset sources, but they must be cleared by the user. When the register is read, it is possible that both flags are set if both have occurred since the user last cleared them. Early Power Fail Comparator An early power fail warning can be provided to the processor well before VDD drops out of spec. The comparator is used to create a power fail interrupt (NMI). This can be accomplished by connecting the PFI pin to the unregulated power supply via a resistor divider. An application circuit is shown below. Figure 5. Comparator as Early Power-Fail Warning + - 1.2V ref Regulator VDD FM31L27x To MCU NMI input CAL/PFO PFI Timebase Counter Watchdog timeout 100 ms clock WDE /RST WR3-0 = 1010b to restart FM31L27x Reset Switch RST MCU Switch Behavior RST FM31L27x drives 100 ms (min.) |
Nº de peça semelhante - FM31L276-GTR |
|
Descrição semelhante - FM31L276-GTR |
|
|
Ligação URL |
Privacy Policy |
ALLDATASHEETPT.COM |
ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |