Os motores de busca de Datasheet de Componentes eletrônicos |
|
ACE93C56 Folha de dados(PDF) 7 Page - ACE Technology Co., LTD. |
|
ACE93C56 Folha de dados(HTML) 7 Page - ACE Technology Co., LTD. |
7 / 14 page ACE93C46.56.66 Three-wire Serial EEPROM VER 1.5 7 Instruction Set for the ACE93C56/66 Instruction SB OP Code Address Data Comments *8 *16 *8 *16 READ 1 10 A8-A0 A7-A0 Read data stored in memory, at specified address EWEN 1 00 11XXXXXX 11XXXXXX Write enable must precede all programming modes REASE 1 11 A8-A0 A7-A0 Erase memory location An-A0 WRITE 1 01 A8-A0 A7-A0 D7-D0 D15-D0 Writes memory location An-A0 ERAL 1 00 10XXXXXXX 10XXXXXX Erases all memory locations. Valid only at VCC=4.5V to 5.5V WRAL 1 00 01XXXXXXX 01XXXXXX D7-D0 D15-D0 Writes all memory locations. Valid only at VCC=4.5V to 5.5V EWDS 1 00 00XXXXXXX 00XXXXXX Disables all programming instructions Notes: The X ’s in the address field represent don’t care values and must be clocked. READ (READ): The Read (READ) instruction contains the address code for the memory location to be read. After the instruction and address are decoded, data from the selected memory location is available at the serial output pin DO. Output data changes are synchronized with the rising edges of serial clock SK. It should be noted that a dummy bit (logic “0”) precedes the 8- or 16-bit data output string. The ACE93C56/66 supports sequential read operations. The device will automatically increment the internal address pointer and clock out the next memory location as long as Chip Select (CS) is held high .In this case ,the dummy bit (logic “0”)will not be clocked out between memory locations, thus allowing for a continuous steam of data to be read. ERASE/WRITE (EWEN): To assure data integrity, the part automatically goes into the Erase/Write Disable (EWDS) state when power is first applied. An Erase/Write Enable(EWEN) instruction must be executed first before any programming instructions can be carried out. Please note that once in the EWEN state, programming remains enabled until an EWDS instruction is executed or VCC power is removed from the part. ERASE (ERASE): The Erase (ERASE) instruction programs all bits in the specified memory location to the logical “1” state. The self-timed erase cycle starts once the ERASE instruction and address are decoded. The DO pin outputs the Ready/Busy status of the part if CS is brought high after being kept low for a minimum of 250 ns (TCS). A logic “1” at pin DO indicates that the selected memory location has been erased, and the part is ready for another instruction. |
Nº de peça semelhante - ACE93C56 |
|
Descrição semelhante - ACE93C56 |
|
|
Ligação URL |
Privacy Policy |
ALLDATASHEETPT.COM |
ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |