Os motores de busca de Datasheet de Componentes eletrônicos
  Portuguese  ▼
ALLDATASHEETPT.COM

X  

AD515 Folha de dados(PDF) 3 Page - Analog Devices

Nome de Peças AD515
Descrição Electrónicos  Monolithic Precision, Low Power FET-Input Electrometer Op Amp
Download  6 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricante Electrônico  AD [Analog Devices]
Página de início  http://www.analog.com
Logo AD - Analog Devices

AD515 Folha de dados(HTML) 3 Page - Analog Devices

  AD515 Datasheet HTML 1Page - Analog Devices AD515 Datasheet HTML 2Page - Analog Devices AD515 Datasheet HTML 3Page - Analog Devices AD515 Datasheet HTML 4Page - Analog Devices AD515 Datasheet HTML 5Page - Analog Devices AD515 Datasheet HTML 6Page - Analog Devices  
Zoom Inzoom in Zoom Outzoom out
 3 / 6 page
background image
–3–
REV. A
AD515A
LAYOUT AND CONNECTIONS CONSIDERATIONS
The design of very high impedance measurement systems in-
troduces a new level of problems associated with the reduction
of leakage paths and noise pickup.
1. A primary consideration in high impedance system designs is
to attempt to place the measuring device as near to the signal
source as possible. This will minimize current leakage paths,
noise pickup and capacitive loading. The AD515A, with its
combination of low offset voltage (normally eliminating the
need for trimming), low quiescent current (minimal source
heating, possible battery operation), internal compensation
and small physical size lends itself to installation at the signal
source or inside a probe. As a result of the high load capaci-
tance rating, the AD515A can comfortably drive a long
signal cable.
2. The use of guarding techniques is essential to realizing the
capability of the ultralow input currents of the AD515A.
Guarding is achieved by applying a low impedance bootstrap
potential to the outside of the insulation material surround-
ing the high impedance signal line. This bootstrap potential
is held at the same level as that of the high impedance line;
therefore, there is no voltage drop across the insulation and,
hence, no leakage. The guard will also act as a shield to
reduce noise pickup and serves an additional function of
reducing the effective capacitance to the input line. The case
of the AD515A is brought out separately to Pin 8 so it can
also be connected to the guard potential. This technique
virtually eliminates potential leakage paths across the package
insulation, provides a noise shield for the sensitive circuitry
and reduces common-mode input capacitance to about 0.8
pF. Figure 1 shows a proper printed circuit board layout for
input guarding and connecting the case guard. Figures 2 and
3 show guarding connections for typical inverting and
noninverting applications. If Pin 8 is not used for guarding, it
should be connected to ground or a power supply to reduce
noise.
Figure 1. Board Layout for Guarding Inputs with Guarded
TO-99 Package
3. Printed circuit board layout and construction is critical for
achieving the ultimate in low leakage performance that the
AD515A can deliver. The best performance will be realized
by using a teflon IC socket for the AD515A; at a minimum a
teflon standoff should be used for the high impedance lead.
If this is not feasible, the input guarding scheme shown in
Figure 1 will minimize leakage as much as possible; the
guard ring should be applied to both sides of the board. The
guard ring is connected to a low impedance potential at the
same level as the inputs. High impedance signal lines should
not be extended for any unnecessary length on a printed
circuit; to minimize noise and leakage, they must be carried
in rigid, shielded cables.
4. Another important concern for achieving and maintaining
low leakage currents is complete cleanliness of circuit boards
and components. Completed assemblies should be washed
thoroughly in a low residue solvent such as TMC Freon or
high purity methanol, followed by a rinse with deionized
water and nitrogen drying. If service is anticipated in a high
contaminant or high humidity environment, a high dielectric
conformal coating is recommended. All insulation materials
except Kel-F or teflon will show rapid degradation of surface
leakage at high humidities.
Figure 2. Picoampere Current-to-Voltage Converter
Inverting Configuration
Figure 3. Very High Impedance Noninverting Amplifier
INPUT PROTECTION
The AD515A is guaranteed for a maximum safe input potential
equal to the power supply potential.
Many instrumentation situations, such as flame detectors in gas
chromatographs, involve measurement of low level currents
from high voltage sources. In such applications, a sensor fault
condition may apply a very high potential to the input of the
current-to-voltage converting amplifier. This possibility necessi-
tates some form of input protection. Many electrometer type
devices, especially CMOS designs, can require elaborate Zener
protection schemes that often compromise overall performance.
The AD515A requires input protection only if the source is not
current limited and, as such, is similar to many JFET-input
designs. The failure mode would be overheating from excess
current rather than voltage breakdown. If the source is not
current limited, all that is required is a resistor in series with the
affected input terminal so that the maximum overload current is
0.1 mA (for example, 1 M
Ω for a 100 V overload). This simple
scheme will cause no significant reduction in performance and
give complete overload protection. Figures 2 and 3 show proper
connections.


Nº de peça semelhante - AD515

Fabricante ElectrônicoNome de PeçasFolha de dadosDescrição Electrónicos
logo
Analog Devices
AD515A AD-AD515A_15 Datasheet
212Kb / 6P
   Monolithic Precision, Low Power FET-Input Electrometer Op Amp
REV. A
More results

Descrição semelhante - AD515

Fabricante ElectrônicoNome de PeçasFolha de dadosDescrição Electrónicos
logo
Analog Devices
AD515A AD-AD515A_15 Datasheet
212Kb / 6P
   Monolithic Precision, Low Power FET-Input Electrometer Op Amp
REV. A
AD545A AD-AD545A Datasheet
280Kb / 4P
   Monolithic Precision, Low Drift FET-Input Op Amp
AD795 AD-AD795_02 Datasheet
278Kb / 16P
   Low Power, Low Noise Precision FET Op Amp
REV. B
AD795 AD-AD795_15 Datasheet
276Kb / 20P
   Low Power, Low Noise Precision FET Op Amp
REV. C
AD795 AD-AD795 Datasheet
331Kb / 16P
   Low Power, Low Noise Precision FET Op Amp
REV. A
AD795 AD-AD795_09 Datasheet
276Kb / 20P
   Low Power, Low Noise Precision FET Op Amp
REV. C
logo
Linear Technology
LT1792 LINER-LT1792 Datasheet
169Kb / 12P
   Low Noise, Precision, JFET Input Op Amp
LT1792 LINER-LT1792_15 Datasheet
184Kb / 12P
   Low Noise, Precision, JFET Input Op Amp
logo
M.S. Kennedy Corporatio...
MSK032 MSK-MSK032 Datasheet
181Kb / 5P
   FET INPUT DIFFERENTIAL OP-AMP
logo
Anaren Microwave
MSK032 ANAREN-MSK032 Datasheet
378Kb / 5P
   FET INPUT DIFFERENTIAL OP-AMP
More results


Html Pages

1 2 3 4 5 6


Folha de dados Download

Go To PDF Page


Ligação URL




Privacy Policy
ALLDATASHEETPT.COM
ALLDATASHEET é útil para você?  [ DONATE ] 

Sobre Alldatasheet   |   Publicidade   |   Contato conosco   |   Privacy Policy   |   roca de Link   |   Lista de Fabricantes
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com