Datasheet

www.rohm.com

TSZ02201-0RAR1G200080-1-2

© 2012 ROHM Co., Ltd. All rights reserved.

4/19

7.NOV.2012 Rev.001

TSZ22111･15･00

BA4510xxx

Description of electrical characteristics

Described here are the terms of electric characteristics used in this datasheet. Items and symbols used are also shown.

Note that item name and symbol and their meaning may differ from those on another manufacture’s document or general document.

1. Absolute maximum ratings

Absolute maximum rating item indicates the condition which must not be exceeded.

Application of voltage in excess of

absolute maximum rating or use out of absolute maximum rated temperature environment may cause deterioration of

characteristics.

1.1 Power supply voltage (VCC/VEE)

Indicates the maximum voltage that can be applied between the positive power supply terminal and negative power

supply terminal without deterioration or destruction of characteristics of internal circuit.

1.2 Differential input voltage (Vid)

Indicates the maximum voltage that can be applied between non-inverting terminal and inverting terminal without

deterioration and destruction of characteristics of IC.

1.3 Input common-mode voltage range (Vicm)

Indicates the maximum voltage that can be applied to non-inverting terminal and inverting terminal without

deterioration or destruction of characteristics. Input common-mode voltage range of the maximum ratings not assure

normal operation of IC. When normal operation of IC is desired, the input common-mode voltage of characteristics

item must be followed.

1.4 Power dissipation (Pd)

Indicates the power that can be consumed by specified mounted board at the ambient temperature 25℃(normal temperature).

As for package product, Pd is determined by the temperature that can be permitted by IC chip in the package

(maximum junction temperature) and thermal resistance of the package.

2. Electrical characteristics item

2.1 Input offset voltage (Vio)

Indicates the voltage difference between non-inverting terminal and inverting terminal. It can be translated into the

input voltage difference required for setting the output voltage at 0 V.

2.2 Input offset current (Iio)

Indicates the difference of input bias current between non-inverting terminal and inverting terminal.

2.3 Input bias current (Ib)

Indicates the current that flows into or out of the input terminal. It is defined by the average of input bias current at

non-inverting terminal and input bias current at inverting terminal.

2.4 Input common-mode voltage range(Vicm)

Indicates the input voltage range where IC operates normally.

2.5 Large signal voltage gain (Av)

Indicates the amplifying rate (gain) of output voltage against the voltage difference between non-inverting terminal

and Inverting terminal. It is normally the amplifying rate (gain) with reference to DC voltage.

Av = (Output voltage fluctuation) / (Input offset fluctuation)

2.6 Circuit current (ICC)

Indicates the IC current that flows under specified conditions and no-load steady status.

2.7 Maximum Output Voltage(High) / Maximum Output Voltage(Low) (VOH/VOL)

Indicates the voltage range that can be output by the IC under specified load condition. It is typically divided into

maximum output voltage High and low. Maximum output voltage high indicates the upper limit of output voltage.

Maximum output voltage low indicates the lower limit.

2.8 Common-mode rejection ratio (CMRR)

Indicates the ratio of fluctuation of input offset voltage when in-phase input voltage is changed. It is normally the

fluctuation of DC.

CMRR = (Change of Input common-mode voltage)/(Input offset fluctuation)

2.9 Power supply rejection ratio (PSRR)

Indicates the ratio of fluctuation of input offset voltage when supply voltage is changed. It is normally the fluctuation

of DC.

PSRR = (Change of power supply voltage) / (Input offset fluctuation)

2.10 Slew Rate (SR)

SR is a parameter that shows movement speed of operational amplifier. It indicates rate of variable output voltage

as unit time.

2.11 Total harmonic distortion + Noise (THD+N)

Indicates the fluctuation of input offset voltage or that of output voltage with reference to the change of output voltage

of driven channel.