Os motores de busca de Datasheet de Componentes eletrônicos
  Portuguese  ▼
ALLDATASHEETPT.COM

X  

ADM1026 Folha de dados(PDF) 11 Page - ON Semiconductor

Nome de Peças ADM1026
Descrição Electrónicos  Complete Thermal System Management Controller
Download  55 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricante Electrônico  ONSEMI [ON Semiconductor]
Página de início  http://www.onsemi.com
Logo ONSEMI - ON Semiconductor

ADM1026 Folha de dados(HTML) 11 Page - ON Semiconductor

Back Button ADM1026 Datasheet HTML 7Page - ON Semiconductor ADM1026 Datasheet HTML 8Page - ON Semiconductor ADM1026 Datasheet HTML 9Page - ON Semiconductor ADM1026 Datasheet HTML 10Page - ON Semiconductor ADM1026 Datasheet HTML 11Page - ON Semiconductor ADM1026 Datasheet HTML 12Page - ON Semiconductor ADM1026 Datasheet HTML 13Page - ON Semiconductor ADM1026 Datasheet HTML 14Page - ON Semiconductor ADM1026 Datasheet HTML 15Page - ON Semiconductor Next Button
Zoom Inzoom in Zoom Outzoom out
 11 / 55 page
background image
ADM1026
http://onsemi.com
11
ADM1026 is powered down, unlike the data in the volatile
registers. Although referred to as read-only memory, the
EEPROM can be written to (as well as read from) via the
serial bus in exactly the same way as the other registers. The
main differences between the EEPROM and other registers
are:
An EEPROM location must be blank before it can be
written to. If it contains data, it must first be erased.
Writing to EEPROM is slower than writing to RAM.
Writing to the EEPROM should be restricted because
its typical cycle life is 100,000 write operations, due to
the usual EEPROM wear-out mechanisms.
The EEPROM in the ADM1026 has been qualified for
two key EEPROM memory characteristics: memory cycling
endurance and memory data retention.
Endurance qualifies the ability of the EEPROM to be
cycled through many program, read, and erase cycles. In real
terms, a single endurance cycle is composed of four
independent, sequential events, as follows:
1. Initial page erase sequence
2. Read/verify sequence
3. Program sequence
4. Second read/verify sequence
In reliability qualification, every byte is cycled from 00h
to FFh until a first fail is recorded, signifying the endurance
limit of the EEPROM memory.
Retention quantifies the ability of the memory to retain its
programmed data over time. The EEPROM in the ADM1026
has been qualified in accordance with the formal JEDEC
Retention Lifetime Specification (A117) at a specific junction
temperature (TJ = 55C) to guarantee a minimum of 10 years
retention time. As part of this qualification procedure, the
EEPROM memory is cycled to its specified endurance limit
described above before data retention is characterized. This
means that the EEPROM memory is guaranteed to retain its
data for its full specified retention lifetime every time the
EEPROM is reprogrammed. Note that retention lifetime
based on an activation energy of 0.6 V derates with TJ, as
shown in Figure 15.
Figure 15. Typical EEPROM Memory Retention
JUNCTION TEMPERATURE (5C)
250
300
100
200
150
50
0
50
60
70
80
90
100
40
110
120
Serial Bus Interface
Control of the ADM1026 is carried out via the serial
system management bus (SMBus). The ADM1026 is
connected to this bus as a slave device, under the control of
a master device.
The ADM1026 has a 7-bit serial bus slave address. When
the device is powered on, it does so with a default serial bus
address. The 5 MSBs of the address are set to 01011, and the
2 LSBs are determined by the logical states of Pin 15
ADD/NTESTOUT. This pin is a three-state input that can be
grounded, connected to VCC, or left open-circuit to give
three different addresses.
Table 6. ADDRESS PIN TRUTH TABLE
ADD Pin
A1
A0
GND
0
0
No Connect
1
0
VCC
0
1
If ADD is left open-circuit, the default address is 0101110
(5Ch). ADD is sampled only at powerup on the first valid
SMBus transaction, so any changes made while the power
is on (and the address is locked) have no effect.
The facility to make hardwired changes to device
addresses allows the user to avoid conflicts with other
devices sharing the same serial bus, for example if more than
one ADM1026 is used in a system.
General SMBus Timing
Figure 16 and Figure 17 show timing diagrams for general
read and write operations using the SMBus. The SMBus
specification defines specific conditions for different types
of read and write operations, which are discussed later in this
section. The general SMBus protocol* operates as follows:
1. The master initiates data transfer by establishing a
start condition, defined as a high-to-low transition
on the serial data line (SDA) while the serial clock
line SCL remains high. This indicates that a data
stream follows. All slave peripherals connected to
the serial bus respond to the start condition and
shift in the next 8 bits, consisting of a 7-bit slave
address (MSB first) and an R/W bit, which
determine the direction of the data transfer, that is,
whether data is written to or read from the slave
device (0 = write, 1 = read).
The peripheral whose address corresponds to the
trans-mitted address responds by pulling the data
line low during the low period before the ninth
clock pulse, known as the acknowledge bit, and
holding it low during the high period of this clock
pulse. All other devices on the bus remain idle
while the selected device waits for data to be read
from or written to it. If the R/W bit is 0, the master
writes to the slave device. If the R/W bit is 1, the
master reads from the slave device.


Nº de peça semelhante - ADM1026

Fabricante ElectrônicoNome de PeçasFolha de dadosDescrição Electrónicos
logo
Analog Devices
ADM1026 AD-ADM1026 Datasheet
634Kb / 56P
   Complete Thermal and System Management Controller
REV. A
logo
ON Semiconductor
ADM1026 ONSEMI-ADM1026 Datasheet
504Kb / 55P
   Complete Thermal System Management Controller
June, 2010 ??Rev. 3
logo
Analog Devices
ADM1026JST AD-ADM1026JST Datasheet
634Kb / 56P
   Complete Thermal and System Management Controller
REV. A
logo
ON Semiconductor
ADM1026JST ONSEMI-ADM1026JST Datasheet
504Kb / 55P
   Complete Thermal System Management Controller
June, 2010 ??Rev. 3
logo
Analog Devices
ADM1026JST-REEL AD-ADM1026JST-REEL Datasheet
634Kb / 56P
   Complete Thermal and System Management Controller
REV. A
More results

Descrição semelhante - ADM1026

Fabricante ElectrônicoNome de PeçasFolha de dadosDescrição Electrónicos
logo
ON Semiconductor
ADM1026 ONSEMI-ADM1026 Datasheet
504Kb / 55P
   Complete Thermal System Management Controller
June, 2010 ??Rev. 3
logo
Analog Devices
ADM1026 AD-ADM1026 Datasheet
634Kb / 56P
   Complete Thermal and System Management Controller
REV. A
logo
National Semiconductor ...
PC87782 NSC-PC87782 Datasheet
123Kb / 17P
   CompactRISC Intelligent System Management Controller
logo
Agilent(Hewlett-Packard...
HDJD-J822 HP-HDJD-J822 Datasheet
143Kb / 19P
   Color Management System Feedback Controller
logo
Texas Instruments
TPS99001-Q1 TI-TPS99001-Q1 Datasheet
2Mb / 50P
[Old version datasheet]   TPS99001-Q1 System Management Controller
logo
AVAGO TECHNOLOGIES LIMI...
HDJD-J822 AVAGO-HDJD-J822 Datasheet
72Kb / 2P
   Color Management System Feedback Controller
logo
Texas Instruments
TPS99000-Q1 TI1-TPS99000-Q1 Datasheet
388Kb / 9P
[Old version datasheet]   System Management and Illumination Controller
TPS99000-Q1 TI1-TPS99000-Q1_18 Datasheet
3Mb / 81P
[Old version datasheet]   System Management and Illumination Controller
logo
AVAGO TECHNOLOGIES LIMI...
HDJD-J822-SCR00 AVAGO-HDJD-J822-SCR00 Datasheet
230Kb / 16P
   Color Management System Feedback Controller
logo
List of Unclassifed Man...
PLW114050 ETC2-PLW114050 Datasheet
260Kb / 3P
   Thermal Management
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55


Folha de dados Download

Go To PDF Page


Ligação URL




Privacy Policy
ALLDATASHEETPT.COM
ALLDATASHEET é útil para você?  [ DONATE ] 

Sobre Alldatasheet   |   Publicidade   |   Contato conosco   |   Privacy Policy   |   roca de Link   |   Lista de Fabricantes
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com