CS8361YN16 datasheet(4/6 Pages) CHERRY

Nome de Peças	CS8361YN16

Descrição Electrónicos	5V Dual Micropower Low Dropout Regulator with ENABLE and RESET

Download	6 Pages

Scroll/Zoom	100%

Fabricante Electrônico	CHERRY [Cherry Semiconductor Corporation]

Página de início	http://www.cherrycorp.com/

Logo

4 / 6 page

4

Circuit Description

Application Notes

The

function switches the output transistor for

VTRK on and off. When the

lead voltage exceeds

1.4V(typ), VTRK turns off. This input has several hundred

millivolts of hysteresis to prevent spurious output activity

during power-up or power-down.

The

is an open collector NPN transistor, con-

trolled by a low voltage detection circuit sensing the VSTBY

(5V) output voltage. This circuit guarantees the

output stays below 1V (0.1V typ) when VSTBY is as low as

1V to ensure reliable operation of microprocessor-based

systems.

This output uses the same type of output device as VSTBY,

but is rated for 250mA. The output is configured as a

tracking regulator of the standby output. By using the

standby output as a voltage reference, giving the user an

external programming lead (Adj lead), output voltages

from 5V to 20V are easily realized. The programming is

done with a simple resistor divider (Figure 2), and follow-

ing the formula:

VTRK = VSTBY ´ (1 + R1/R2) + IAdj ´ R1

If another 5V output is needed, simply connect the Adj

lead to the VTRK output lead.

VTRK Output Voltage

RESET

RESET Function

ENABLE

ENABLE Function

Output capacitors for the CS8361 are required for stability.

Without them, the regulator outputs will oscillate. Actual

size and type may vary depending upon the application

load and temperature range. Capacitor effective series

resistance (ESR) is also a factor in the IC stability. Worst-

case is determined at the minimum ambient temperature

and maximum load expected.

Output capacitors can be increased in size to any desired

value above the minimum. One possible purpose of this

would be to maintain the output voltages during brief

conditions of negative input transients that might be char-

acteristic of a particular system.

Capacitors must also be rated at all ambient temperatures

expected in the system. To maintain regulator stability

down to -40ûC, capacitors rated at that temperature must

be used.

More information on capacitor selection for Smart

Regulatorsª is available in the Smart Regulator applica-

tion note, ÒCompensation for Linear Regulators.Ó

The maximum power dissipation for a dual output regula-

tor (Figure 1) is:

PD(max) = {VIN(max)ÐVOUT1(min)}IOUT1(max)+

{VIN(max)ÐVOUT2(min)}IOUT2(max)+VIN(max)IQ

(1)

Where

VIN(max) is the maximum input voltage,

VOUT1(min) is the minimum output voltage from VOUT1,

VOUT2(min) is the minimum output voltage from VOUT2,

IOUT1(max) is the maximum output current, for the

application

IOUT2(max) is the maximum output current, for the

application

IQ is the quiescent current the regulator consumes at

IOUT(max).

Once the value of PD(max) is known, the maximum per-

missible value of RQJA can be calculated:

RQJA =

(2)

The value of RQJA can then be compared with those in

the package section of the data sheet. Those packages

with RQJA's less than the calculated value in equation 2

will keep the die temperature below 150¡C.

In some cases, none of the packages will be sufficient to

dissipate the heat generated by the IC, and an external

heat sink will be required.

Figure 1: Dual output regulator with key performance parameters

labeled.

VIN

VOUT2

IIN

IQ

Control

Features

}

IOUT2

VOUT1

IOUT1

Smart

Regulator

150¡C - TA

PD

Calculating Power Dissipation

in a Dual Output Linear Regulator

External Capacitors

Nº de peça semelhante - CS8361YN16

Fabricante Electrônico	Nome de Peças	Folha de dados	Descrição Electrónicos
ON Semiconductor	CS8361YDPS7G	163Kb / 8P	5.0 V Dual Micropower Low Dropout Regulator with ENABLE and RESET October, 2009 ??Rev. 17
	CS8361YDPSR7G	163Kb / 8P	5.0 V Dual Micropower Low Dropout Regulator with ENABLE and RESET October, 2009 ??Rev. 17
	CS8361YDWF16G	163Kb / 8P	5.0 V Dual Micropower Low Dropout Regulator with ENABLE and RESET October, 2009 ??Rev. 17
	CS8361YDWFR16G	163Kb / 8P	5.0 V Dual Micropower Low Dropout Regulator with ENABLE and RESET October, 2009 ??Rev. 17

More results

Descrição semelhante - CS8361YN16

Fabricante Electrônico	Nome de Peças	Folha de dados	Descrição Electrónicos
Cherry Semiconductor Co...	CS8101	196Kb / 8P	Micropower 5V, 100mA Low Dropout Linear Regulator with RESET and ENABLE
Cherry Semiconductor Co...	CS8135	180Kb / 8P	5V, 5V Low Dropout Dual Regulator with /ENABLE RESET
ON Semiconductor	CS8363	69Kb / 8P	3.3 V Dual Micropower Low Dropout Regulator with ENABLE and RESET January, 2004 ??Rev. 9
	CS8363	64Kb / 8P	3.3 V Dual Micropower Low Dropout Regulator with ENABLE and RESET March, 2005 ??Rev. 10
	CS8361	163Kb / 8P	5.0 V Dual Micropower Low Dropout Regulator with ENABLE and RESET October, 2009 ??Rev. 17
Cherry Semiconductor Co...	CS8281	153Kb / 6P	5V/250mA, 5V/100mA Micropower Low Dropout Regulator with ENABLE
	CS8391	152Kb / 6P	5V/250mA, 5V/100mA Micropower Low Dropout Regulator with ENABLE
	CS8161	198Kb / 8P	12V, 5V Low Dropout Dual Regulator with ENABLE
	CS8147	173Kb / 8P	10V/5V Low Dropout Dual Regulator with ENABLE
	CS8156	172Kb / 8P	12V, 5V Low Dropout Dual Regulator with ENABLE

More results

CS8361YN16 Folha de dados(PDF) 4 Page - Cherry Semiconductor Corporation

CS8361YN16 Folha de dados(HTML) 4 Page - Cherry Semiconductor Corporation

Nº de peça semelhante - CS8361YN16

Descrição semelhante - CS8361YN16

Html Pages

1 2 3 4 5 6

Folha de dados Download

Ligação URL