Os motores de busca de Datasheet de Componentes eletrônicos |
|
3--304052--6 Folha de dados(PDF) 7 Page - Tyco Electronics |
|
3--304052--6 Folha de dados(HTML) 7 Page - Tyco Electronics |
7 / 9 page 408- 10029 PIDG and PLASTI- GRIP Terminal and Splice Crimping Heads 7 of 9 Rev B Tyco Electronics Corporation 6.4. Lubrication Lubricate all pins, pivot points, and bearing surfaces with a high quality grease. Tyco Electronics recommends the use of MolykoteS grease, which is a commercially available lubricant. Lubricate according to the following schedule: Head used in daily production -- lubricate daily Head used daily (occasional) -- lubricate weekly Head used weekly -- lubricate monthly Wipe excess grease from crimping head, particularly from jaw closure areas. Grease transferred from jaw closure area onto certain terminations may affect the electrical characteristics of an application. 6.5. Gaging the Crimping Chamber This inspection requires the use of plug gages conforming to the dimensions shown in Figure 7. Tyco Electronics does not manufacture or market these gages. GO Dia NO--GO Dia 50.8 [2.0] Min. Typ. Jaw Closure Configuration Suggested Plug Gage Design Wire Barrel Crimp CRIMPING HEAD JAW CLOSURE GAGE ELEMENT DIAMETERS HEAD CLOSURE DIMENSIONS GO NO--GO 1--47386--0 1--47386--4 1--525690--0 2.769--2.921 [.1090--.1150] 2.769--2.776 [.1090--.1093] 2.918--2.921 [.1149--.1150] 1--47387--0 1--47387--7 1--525691--0 3.023--3.175 [.1190--.1250] 3.023--3.030 [.1190--.1193] 3.172--3.175 [.1249--.1250] 1--46121--0 1.600--1.752 [.0630--.0690] 1.600--1.608 [.0630--.0633] 1.750--1.752 [.0689--.0690] Figure 7 (cont’d) S Molykote is a trademark. Suggested Plug Gage Design Insulation Crimp GO Dim. NO--GO Dim. 6.35 [.250] Typ. 3.18 [.125] GO NO GO Jaw Closure Configuration CRIMPING HEAD JAW CLOSURE GAGE ELEMENT DIAMETERS HEAD CLOSURE DIMENSIONS GO NO--GO 1--525690--0 0.889--1.397 [.0350--.0550] 0.889--0.897 [.0350--.0353] 1.394--1.397 [.0549--.0550] 1--47386--0 1--47386--4 0.762--1.270 [.0300--.0500] 0.762--0.770 [.0300--.0303] 1.267--1.270 [.0499--.0500] 1--47387--0 1--47387--7 1.016--1.524 [.0400--.0600] 1.016--1.024 [.0400--.0403] 1.521--1.524 [.0599--.0600] 1--46121--0 0.762--1.270 [.0300--.0500] 0.762--0.770] [.0300--.0303] 1.267--1.270 [.0499--.0500] 1--525691--0 1.143--1.651 [.0450--.0650] 1.143--1.151 [.0450--.0453] 1.648--1.651 [.0649--.0650] Figure 7 (end) Disconnect the battery and remove crimping head from tool before inspecting crimping chambers. 1. Remove oil and dirt from the jaw bottoming surfaces and plug gage element surfaces. 2. Close wire barrel crimping jaws until they are bottomed, but not under pressure. 3. Align GO element with wire barrel crimping section. Push element straight into crimping chamber without using force. The GO element must pass completely through the chamber as shown in Figure 8A. 4. Align the NO--GO element and try to insert it into the chamber. The element may start entry, but it must not pass completely through the crimping chamber. 5. Repeat this procedure for the insulation crimping section using a plug gage as shown in Figure 8B. If the crimping chamber passes the gage inspection, the crimping head is considered dimensionally correct and should be lubricated with a THIN coat of any good SAE 20 motor oil. If the crimping chamber does not conform to the plug gage conditions, contact your local Tyco Electronics Field Representative or refer to Section 7, REPLACEMENT AND REPAIR. For additional information about the use of a plug gage, see Instruction Sheet 408--7424. DANGER |
Nº de peça semelhante - 3--304052--6 |
|
Descrição semelhante - 3--304052--6 |
|
|
Ligação URL |
Privacy Policy |
ALLDATASHEETPT.COM |
ALLDATASHEET é útil para você? [ DONATE ] |
Sobre Alldatasheet | Publicidade | Contato conosco | Privacy Policy | roca de Link | Lista de Fabricantes All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |