Os motores de busca de Datasheet de Componentes eletrônicos
  Portuguese  ▼
ALLDATASHEETPT.COM

X  

4--21028--9 Folha de dados(PDF) 3 Page - Tyco Electronics

Nome de Peças 4--21028--9
Descrição Electrónicos  Pneumatic CERTI-CRIMP Tool Holder
Download  4 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Fabricante Electrônico  MACOM [Tyco Electronics]
Página de início  http://www.macom.com
Logo MACOM - Tyco Electronics

4--21028--9 Folha de dados(HTML) 3 Page - Tyco Electronics

  4--21028--9 Datasheet HTML 1Page - Tyco Electronics 4--21028--9 Datasheet HTML 2Page - Tyco Electronics 4--21028--9 Datasheet HTML 3Page - Tyco Electronics 4--21028--9 Datasheet HTML 4Page - Tyco Electronics  
Zoom Inzoom in Zoom Outzoom out
 3 / 4 page
background image
408- 4303
Pneumatic CERTI- CRIMP Tool Holder Assemblies 356302- 1, 356303- 1, and 1673611- 1
3
of 4
Rev F
Tyco Electronics Corporation
Figure 3
Ratchet Pawl with
Emergency Release
Press Pawl with
Screwdriver
6. If the ratchet does not release after the jaws or
dies bottom, loosen the three securing screws,
remove the eccentric adjustment screw and rotate
the eccentric counterclockwise to a lower setting.
Repeat as required.
7. If the crimp cannot be made to conform to the
dimensions provided in the appropriate application
specification (114--series), the crimping head
and/or dies are defective and must be replaced.
5. MAINTENANCE AND INSPECTION
To avoid injury, DISCONNECT TOOL FROM AIR
SUPPLY before performing any maintenance or
inspection procedures.
It is recommended that a maintenance and inspection
program be performed periodically to ensure
dependable and uniform terminations. The tool holder
should be inspected once a week. Frequency of
inspection should be adjusted to suit your
requirements through experience, and depends on:
1. Care, amount of use, and handling of the tool.
2. Type and size of the products crimped.
3. Degree of operator skill.
4. Presence of abnormal amounts of dust and dirt.
5. Your own established standards.
The tool holder is thoroughly inspected before
packaging. Since there is the possibility of damage
during shipment, the tool holder should be inspected
immediately upon arrival at your facility.
5.1. Maintenance
A. Cleaning
Remove dust, moisture, and other contaminants with
a clean, soft brush, or a soft, lint--free cloth. Do NOT
use objects that could damage the tool. Re--lubricate
tool holder (refer to Paragraph 5.1,B) before placing it
back into service.
B. Lubrication
Lubricate all pins, pivot points, and bearing surfaces
with a high quality grease. (Commercially available
Molykote grease is recommended.) Lubricate
according to the following schedule:
Holder used in daily production—lubricate daily
Holder used daily (occasional)—lubricate weekly
Holder used weekly—lubricate monthly
Wipe excess grease from tool holder, particularly from
jaw or die closure areas. Grease transferred from the
jaw or die closure area onto certain terminations may
affect the electrical characteristics of an application.
5.2. Periodic Inspection
Regular inspections of the tool should be performed
by quality control personnel. A record of scheduled
inspections should remain with the tool or be supplied
to supervisory personnel responsible for the tool.
Inspection frequency should be based upon amount
of use, working conditions, operator training and skill,
and established company standards.
1. Inspect the tool holder for missing pins or parts.
If parts are missing or defective, replace them by
referring to Section 6.
2. Check all bearing surfaces for wear. Make sure
the rollers on the crimping head turn freely with
minimal resistance. Replace any worn parts.
3. Inspect crimping jaws or dies for flattened,
chipped, or broken areas. Worn or damaged
surfaces are objectionable and will affect the
quality of the crimp.
4. When the tool is not in use, store in a clean, dry
area.
6. REPLACEMENT AND REPAIR
Replaceable parts are listed in Figure 4. Parts other
than those listed in Figure 4 should be replaced by
Tyco Electronics to ensure quality and reliability of the
tool. Order replacement parts through your Tyco
Electronics Representative, or call 1--800--526--5142,
or send a facsimile of your purchase order to
1--717--986--7605, or write to:
CUSTOMER SERVICE
TYCO ELECTRONICS
P.O. BOX 3608
HARRISBURG, PA 17105--3608
For tool repair service, please contact a Tyco
Electronics Representative at 1--800--526--5136.
DANGER


Nº de peça semelhante - 4--21028--9

Fabricante ElectrônicoNome de PeçasFolha de dadosDescrição Electrónicos
logo
Tyco Electronics
4--21028--9 MACOM-4--21028--9 Datasheet
139Kb / 4P
   Pneumatic CERTI-CRIMP Tool
More results

Descrição semelhante - 4--21028--9

Fabricante ElectrônicoNome de PeçasFolha de dadosDescrição Electrónicos
logo
Tyco Electronics
408-4321 MACOM-408-4321 Datasheet
139Kb / 4P
   Pneumatic CERTI-CRIMP Tool
408-10021 MACOM-408-10021 Datasheet
530Kb / 5P
   The CERTI--CRIMP II Tool Holder Assembly
logo
List of Unclassifed Man...
WA23 ETC-WA23 Datasheet
1Mb / 3P
   HEAVY DUTY PNEUMATIC CRIMP TOOL
REV.E
logo
Tyco Electronics
1583007 MACOM-1583007 Datasheet
94Kb / 1P
   CERTI- CRIMP II TOOL DATA SHEET EI SERIES CONNECTORS
logo
TE Connectivity Ltd
411-1050 TEC-411-1050 Datasheet
371Kb / 5P
   CERTI-CRIMP Hand Tools
408-7235 TEC-408-7235 Datasheet
69Kb / 4P
   CERTI-CRIMP Hand Crimping Tools
logo
List of Unclassifed Man...
AMT23B ETC2-AMT23B Datasheet
1Mb / 1P
   ENVELOPE DRAWING PNEUMATIC CRIMP TOOL (REF:M22520/23-01)
logo
Tyco Electronics
59824-1 MACOM-59824-1 Datasheet
4Mb / 8P
   Premium CERTI-CRIMP II Hand Tools
logo
PHOENIX CONTACT
SF-Z0022 PHOENIX-SF-Z0022 Datasheet
44Kb / 2P
   Pneumatic crimping tool
logo
Molex Electronics Ltd.
64007-7100 MOLEX11-64007-7100 Datasheet
29Kb / 1P
   Crimp Head for the AT-200 Pneumatic Hand Tool
More results


Html Pages

1 2 3 4


Folha de dados Download

Go To PDF Page


Ligação URL




Privacy Policy
ALLDATASHEETPT.COM
ALLDATASHEET é útil para você?  [ DONATE ] 

Sobre Alldatasheet   |   Publicidade   |   Contato conosco   |   Privacy Policy   |   roca de Link   |   Lista de Fabricantes
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com